How it Works
Lightronics
Loading...
FXLD348R3I
User Manual
6 pgs251.64 Kb0

Lightronics FXLD348R3I User Manual

Download
Page 1 of 5 FXLD348R3I LED FIXTURE
Version 0.1 OWNERS MANUAL 02/16/2012
FEATURES AND SPECIFICATIONS
DESCRIPTION
The FXLD348R3I is a RGB LED lighting fixture. It is suitable for stage, disco, night club, and other artistic applications. It has several stand alone control modes, a master/slave mode, and can operate via a DMX-512 external signal.
A double yoke enables it to be operated in several positions.
INSTALLATION
LOCATION
The FXLD348R3I is rated IP20 and is intended for
INDOOR USE ONLY.
Locate the unit in a well ventilated area away from moisture and heat. Holes are provided on the yokes to install a lighting bar pipe clamp. A safety cable should also be used.
POWER CONNECTIONS
The FXLD348R3I has a line cord for connection to a 120 VAC, 15 Amp, 60Hz, grounded service.
RISK OF ELECTRIC SHOCK
CAUTION
The safety ground pin on the power cord must be used.
DMX CONNECTIONS
A system using DMX control should be connected as a chain of devices. In other words the control signal cable should proceed from the controller to the first
receiving device and then to others in a continuous "daisy chain" fashion.
The fixture has a DMX IN and a DMX OUT connector to be used to connect the chain. The control cable should NOT be split into a multiple run star arrangement with a cable running from the controller directly to each receiving device pack.
DMX CONNECTOR PIN ASSIGNMENTS
There are two different connectors which can be used for DMX control. They are both XLR type connectors. Some units use 3 pin connectors. Others use 5 pin connectors. The FXLD348R3I receives a DMX signal on the 3 pin MALE connector on the back of the unit. The 3 pin FEMALE connector is used to connect the next DMX device on the control chain. If your console uses a 5 pin connector you can make up an adapter cable to accommodate this. The table below shows the pin assignments for BOTH the 3 pin and 5 pin connectors.
DMX TERMINATION
IN # SIGNAL NAME
1 DMX COMMON 2 DMX DATA ­3 DMX DATA + 4 NOT USED 5 NOT USED
A DMX chain should be terminated at the last receiving device on the chain. This is done by installing a commonly available 1/4 Watt, 120 Ohm resistor across the DATA - and DATA + wires at the
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 2 of 5 FXLD348R3I LED FIXTURE Version 0.1 OWNERS MANUAL 02/16/2012
last device. If you have only a few fixtures very close together and a very short run to the controller then you may be able to operate without the terminator.
OPERATION
A control panel on one side of the unit is used to set the operating options. It consists of an LED display and four buttons
(MENU, UP, DOWN, and ENTER)
CONTROL PANEL
Push
UP
MENU UP DOWN ENTER
MENU
to access the operating options. Then use
and
DOWN
to scroll through the available choices.
When you reach the option you want to set or change -
ENTER
push for the option and/or change it. Push
. Now you can view the current setting
ENTER
to save your changes and activate the option. See the "MENU NAVIGATION" diagram for additional details.
There are 7 operation modes: DMX, Blue Level, Green Level, Red Level, Test Colors, Auto Sequence, Run Program, and Slave Mode.
DMX OPERATION
Use the d - - - menu to set the starting address of the unit. You can set the starting address of the unit with the UP and DOWN buttons.
The fixture uses three channels with allocations as follows:
CHANNEL 1: 0 - 255 Red level (255 = Maximum) CHANNEL 2: 0 - 255 Green level (255 = Maximum) CHANNEL 3: 0 - 255 Blue level (255 = Maximum)
MANUAL OPERATION
For manual operation the red, green, and blue LED intensity levels may be independently controlled. Use the Cb - -, Cg - -, and Cr - -, menus to set the levels. The range is from 00 (OFF) to 30 (Full On).
TEST COLORS
The Test Colors option runs all LEDs at the level selected in its menu. Use the E - - - menu to set the level. The range is from 000 to 255. 255 is maximum.
AUTO SEQUENCE
The AUTO SEQUENCE mode switches continuously through a sequence of all the preset programs . See the RUN PROGRAM menu for more details. Use the Au - - menu to set the sequence speed and activate the option. The range is from 00 to 99. 99 is fastest.
RUN PROGRAM
The unit can operate using 55 preset programs. Preset 0 is "all off". Presets 1 through 7 are solid colors. The remaining presets are a variety of changing patterns. Use the Pr - - menu to select and activate a preset program. The range is from 00 to 55.
MASTER/SLAVE OPERATION
The FXLD348R3I can operate in a Master/Slave mode where one of the units can synchronize other units of the same model.
Connect the units together using the DMX IN and DMX OUT connectors. Set the unit to be the Master in one of the modes above. Use the SLAV menu to set a unit as a slave.
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 3 of 5 FXLD348R3I LED FIXTURE
Version 0.1 OWNERS MANUAL 02/16/2012
MAINTENANCE AND REPAIR
TROUBLESHOOTING
Check that you have power applied to the unit. Check the fuse. Check the DMX control cable. Check the address settings of the unit and the
controller.
REPAIR
CAUTION DO NOT OPEN UNIT
RISK OF ELECTRIC SHOCK
RISK OF FIRE
The FXLD348R3I does not contain any user serviceable parts.
Internal service on the unit by other than Lightronics authorized agents will void the warranty. If service is required, contact the dealer from whom you purchased the item, or contact the Lightronics, Service Department, 509 Central Drive, Virginia Beach, VA
23454. Tel: 757 486 3588.
PHOTOMETRIC CHARACTERISTICS
Distance Illuminance Beam Diam. (ft) (Lux) (ft)
6.5 7800 3 20 620 10 30 290 15
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 4 of 5 FXLD348R3I LED FIXTURE
Version 0.1 OWNERS MANUAL 02/16/2012
MENU NAVIGATION
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Y
This product is warranted for a period of TWO YEARS from the date of purchase against defects in materials and workmanship.
This warranty is subject to the following restrictions and conditions:
A) If service is required, you may be asked to provide proof of purchase from an authorized Lightronics dealer.
B) This warranty is valid only for the original purchaser of the unit. C) This warranty does not apply to damage resulting from abuse, misuse, accidents, shipping,
and repairs or modifications by anyone other than an authorized Lightronics service representative.
D) This warranty is void if the serial number is removed, altered or defaced. E) This warranty does not cover loss or damage, direct or indirect arising from the use or
inability to use this product. F) Lightronics reserves the right to make any changes, modifications, or updates as deemed
appropriate by Lightronics to products returned for service. Such changes may be made without prior notification to the user and without incurring any responsibility or liability for modifications or changes to equipment previously supplied. Lightronics is not responsible for supplying new equipment in accordance with any earlier specifications.
G) This warranty is the only warranty either expressed, implied, or statutory, upon which the equipment is purchased. No representatives, dealers or any of their agents are authorized to make any warranties, guarantees, or representations other than expressly stated herein.
H) This warranty does not cover the cost of shipping products to or from Lightronics for service.
I) Lightronics Inc. reserves the right to make changes as deemed necessary to this warranty without prior notification.
WARRANT
Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 20100211
www.lightronics.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use