How it Works
Lightronics
Loading...
FXLD336ZM3I
User Manual
6 pgs291.96 Kb0

Lightronics FXLD336ZM3I User Manual

Download
Page 1 of 5 FXLD336ZM3I LED FIXTURE
Version 0.1 OWNERS MANUAL 02/21/2012
FEATURES AND SPECIFICATIONS
DESCRIPTION
The FXLD336ZM3I is a PAR style RGB LED lighting fixture with zoom capability. It is suitable for stage, disco, night club, and other artistic applications. It has several stand alone control modes, a master/slave mode, and can operate via a DMX-512 external signal.
A double yoke enables it to be operated in several positions.
INSTALLATION
LOCATION
The FXLD336ZM3I is intended for
and is rated IP20.
ONLY
INDOOR USE
Locate the unit in a well ventilated area away from moisture and heat. Holes are provided on the yokes to install a lighting bar pipe clamp. A safety cable should also be used. Do not block any vent holes.
POWER CONNECTIONS
The FXLD336ZM3I has a line cord for connection to a 120 VAC, 15 Amp, 60Hz, grounded service.
RISK OF ELECTRIC SHOCK
CAUTION
The safety ground pin on the power cord must be used.
DMX CONNECTIONS
A system using DMX control should be connected as a chain of devices. In other words the control signal cable should proceed from the controller to the first
receiving device and then to others in a continuous "daisy chain" fashion.
The fixture has a DMX IN and a DMX OUT connector to be used to connect the chain. The control cable should NOT be split into a multiple run star arrangement with a cable running from the controller directly to each receiving device pack.
DMX CONNECTOR PIN ASSIGNMENTS
There are two different connectors which can be used for DMX control. They are both XLR type connectors. Some units use 3 pin connectors. Others use 5 pin connectors. The FXLD336ZM3I receives a DMX signal on the 3 pin MALE connector on the back of the unit. The 3 pin FEMALE connector is used to connect the next DMX device on the control chain. If your console uses a 5 pin connector you can make up an adapter cable to accommodate this. The table below shows the pin assignments for BOTH the 3 pin and 5 pin connectors.
IN # SIGNAL NAME
1 DMX COMMON 2 DMX DATA ­3 DMX DATA + 4 NOT USED 5 NOT USED
www.lightronic.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 2 of 5 FXLD336ZM3I LED FIXTURE
Version 0.1 OWNERS MANUAL 02/21/2012
DMX TERMINATION
A DMX chain should be terminated at the last receiving device on the chain. This is done by installing a commonly available 1/4 Watt, 120 Ohm resistor across the DATA - and DATA + wires at the last device. If you have only a few fixtures very close together and a very short run to the controller then you may be able to operate without the terminator.
OPERATION
Operating options are set using the LED display and 4 buttons
(MENU, ENTER, UP, DOWN)
on the rear of
the fixture.
FXLD336ZM3I REAR VIEW
Push
MENU
to access the operating options. Then use
UP
and
DOWN
to scroll through the available choices. When you reach the option you want to set or change ­push
ENTER
for the option and or change it. Push your changes. Push
. Now you can view the current setting
ENTER
MENU
to return to the current
to save
option display. See the "MENU NAVIGATION" diagram for additional details.
There are 4 main operation modes: DMX, Auto Program, Sound, Master/Slave. There is also a provision to control the zoom function.
DMX OPERATION
Use the ADDR menu to set the starting address of the unit. You can set the starting address of the unit with the UP and DOWN buttons.
The fixture uses six DMX channels with allocations as follows:
CHANNEL 1: 0 - 255 Master Level CHANNEL 2: 0 - 255 Red Level (255 max.) CHANNEL 3: 0 - 255 Green Level (255 max) CHANNEL 4: 0 - 255 Blue Llevel (255 max.) CHANNEL 5: 0 - 255 Strobe Effects CHANNEL 6: 12º - 60º Zoom Control
ZOOM CONTROL
The fixture can zoom its beam diameter between 12º
º
and 60 000 - 255 is the value range. 000 is 12
degrees. Use the FoCS menu to control it.
º
and 255 is 60º.
AUTO PROGRAM OPERATION
Auto Program operation includes 14 (00 - 13) colors and patterns which can be run. There are also speed and fade sub-functions to control the selected program. Use the Pr - - menu to select a program.
Use the Sp - - and FA - - menus to control the speed and fade rates.
SOUND OPERATION
Use the SOUA menu to invoke the Sound Color option. The unit will sequence through a series of colors in sync with music base notes.
MASTER/SLAVE OPERATION
Connect the units together using DMX cables. Set all the units to be slaved to DMX address 001. Set the master unit to any auto operation option. The slave units will sync to the masters operation.
MAINTENANCE AND REPAIR
TROUBLESHOOTING
Check that you have power applied to the unit. Check the DMX control cable. Check the address settings of the unit and the
controller.
www.lightronic.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 3 of 5 FXLD336ZM3I LED FIXTURE
Version 0.1 OWNERS MANUAL 02/21/2012
REPAIR
CAUTION DO NOT OPEN UNIT
RISK OF ELECTRIC SHOCK
RISK OF FIRE
Internal service on the unit by other than Lightronics authorized agents will void the warranty.
If service is required, contact the dealer from whom you purchased the item, or contact the Lightronics, Service Department, 509 Central Drive, Virginia Beach, VA 23454. Tel: 757 486 3588.
PHOTOMETRIC CHARACTERISTICS
Distance Illuminance Beam Diam. (ft) (Lux) (ft) 12º / 60º 12º / 60º
10 1806 / 531 3 / 8 20 481 / 145 6 / 14 30 220 / 75 10 / 20
www.lightronic.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Page 4 of 5 FXLD336ZM3I LED FIXTURE
Version 0.1 OWNERS MANUAL 02/21/2012
MENU NAVIGATION
www.lightronic.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Y
This product is warranted for a period of TWO YEARS from the date of purchase against defects in materials and workmanship.
WARRANT
This warranty is subject to the following restrictions and conditions:
A) If service is required, you may be asked to provide proof of purchase from an authorized Lightronics dealer.
B) This warranty is valid only for the original purchaser of the unit. C) This warranty does not apply to damage resulting from abuse, misuse, accidents, shipping,
and repairs or modifications by anyone other than an authorized Lightronics service representative.
D) This warranty is void if the serial number is removed, altered or defaced. E) This warranty does not cover loss or damage, direct or indirect arising from the use or
inability to use this product. F) Lightronics reserves the right to make any changes, modifications, or updates as deemed
appropriate by Lightronics to products returned for service. Such changes may be made without prior notification to the user and without incurring any responsibility or liability for modifications or changes to equipment previously supplied. Lightronics is not responsible for supplying new equipment in accordance with any earlier specifications.
G) This warranty is the only warranty either expressed, implied, or statutory, upon which the equipment is purchased. No representatives, dealers or any of their agents are authorized to make any warranties, guarantees, or representations other than expressly stated herein.
H) This warranty does not cover the cost of shipping products to or from Lightronics for service.
I) Lightronics Inc. reserves the right to make changes as deemed necessary to this warranty without prior notification.
Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 20100211
www.lightronic.com Lightronics Inc. 509 Central Drive Virginia Beach, Va 234354 757 486 3588
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use