Lightolier SL205A User Manual

SL205A

4 5/8"

(117mm)

8 5/8"

(219mm)

6 3/8"

(162mm)

Decorative, Spectral, Floating Paper, Optic Forms

Page 1 of 3

11 ½"

(292mm)

8 ⅝"

(219mm)

10 ½"

(267mm)

4 ⅝"

(117mm)

6 ⅜"

(162mm)

Ceiling Cutout: 5 1⁄16" (128mm)

Ordering Guide (2 Part System: Trim and Frame-In-Kit)

Trim Frame-In-Kit Lamp Volt Finish

SL2 05AT

*Use 4100K lamp for optimal white lens rendering

4118VU 1-18W TTT 120/277V Clear acrylic with white lacquer lens

4118V-347 1-18W TTT 347V

1 ⅛" MAX.

(29mm)

and stainless steel trim ring.

Job Information Type:

Job Name:

Cat. No.:

Notes:

SL205A

4 5/8"

(117mm)

8 5/8"

(219mm)

6 3/8"

(162mm)

Decorative, Spectral, Floating Paper, Optic Forms

Page 2 of 3

11 ½"

(292mm)

8 ⅝"

(219mm)

10 ½"

(267mm)

4 ⅝"

(117mm)

6 ⅜"

(162mm)

Features

1. Reflector: Specular aluminum, 16 ga. comfort clear low

iridescence finish.

2. Lens: 1 ⅛" (29mm) thick clear acrylic finished with a

translucent diffused coating.

3. Trim Ring: 12 ga. aluminum. Stainless Steel finish.

4. Socket Cup: Heat dissipating die-cast aluminum. Positive

locking attachment, without tools, to reflector assures

proper optical alignment of lamp.

5. Mounting Frame: Die-cast aluminum suitable for dry

ceilings.

6. Retaining Springs: Rust resistant springs simplify reflector/

housing removal for inspection and maintenance.

7. Mounting Brackets: 16 ga. steel. Use 18" (457mm)

mounting bars (optional) or with standard ¾" (19mm), 1 ½"

(38mm) lathing channels (by others) or ½" (13mm) tubing

(by others). Adjust vertically from inside of fixture.

8. Junction Box: 14 ga. steel, 4" (102mm) x 3 ½" (89mm x 2"

(51mm) box, allows inspection from below. UL “c/us” listed

for through branch circuit wiring with maximum of 8 no. 12,

90º C conductors.

9. Screws: Stainless Steel, Philips head.

Mounting

Recessed, Non-IC Type (non thermal insulation contact).

Luminaire Weight: 4 lbs.

1 ⅛" MAX.

(29mm)

Electrical

Ballast: Electronic Program Rapid Start T4 quad lamp ballast.

Universal voltage “U” ballast automatically detects 120 volts

or 277 volts operation. No visible flicker on starting, internally

fused and protection circuit for lamp end of life. Sound rated

“A”. Designed for removal without tools from inside of

luminaire for easy field inspection or service replacement.

TA: 18W TTT non-dimming

Lampholder: GX24q-2 base, 4 Pin.

Options and Accessories

Mounting Bars:

1950, set of 2, 18" (457mm) long.

1951, set of 2, 30" (762mm) long.

T-Bar Anchor Clips:

1956, set of 4, for anchoring mounting bars to T-Bar runners.

Dimming Ballast*

Labels

cULus Listed. Suitable for wet locations.

Job Information Type: