Lightolier S-6497 User Manual
/’-
INSTRUCTIONS FOR AllACHING MR-16
FRAMING PROJECTOR ACCESSORY
FOR USE WITH LYTESPAN’) TRACK SYSTEMS ONLY.
INSTRUCTION SHEET NO “
IS:6497
R0590
Page 1 of 2
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code and local re ulations. To assure
full compliance with local codes and regulations, check with your local electrical inspector be ore installation. To
prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
1
Turn the fixtures OFF and allow the LAMP to cool before
attaching the PROJECTER ACCESSORY.
2,
Remove LAM PHOLDER ASSEMBL.Y from fixture. See
Fig. 1. Note. Style of Iampholder ~sseinbly will vary from
fixture to fixture.
Flernove MR-16 lAMP and GLASS LAMP GL!ARD from
3.
lAMPHOLDER ASSEMBLY.
Remove the INNER RING from PROJECTOR ACCESSORY
4.
by backing out the (2) LOCKING SCREWS (see Fig. 2).
5.
Slip the INNER RING through the LAMP HOLDER
ASSEMBLY making sure the notches in INNER RING
clear the springs or inner ribs.
Slide the PROJECTOR ACCESSORY over the LAMP
6.
HOLDER ASSEMBLY. When properly positioned, hole in
INNER RING will be aligned to accept LOCKING
SCREWS.
7.
Install LOCKING SCREWS half-way. Turn the PROJECTOR
ACCESSORY clockwise until it is tight against the LAMP
HOLDER .4SSEMBLY. Tighten locking screws.
NOTCHES .,,
FIG. 1
..
A
Da
u
?
MR.16 LAMP
LAMPHOLDER
ASSEMBLY
GIASS LAMP GUAR
----
INNER RING
I
8.
Replace the GLASS LAMP GUARD, install the proper
wattage LAMP, and attach the LAMP ASSEMBLY with
PROJECTOR ACCESSORY back on the fixture (see Fig. 3),
Turn the fixture ON and adjust the SHUTTER BLADES to
9.
frame object and focus the LENS for the sharpest beam.
SHUTTER
LENS
FIG. 3
WARNING: LAMP MANUFA~URERS REQUIRE THE GIASS LAMP GUARD BE IN PLACE BEFORE ENERGIZING
LAMP, AND THAT GREAT CARE SHOULD BE TAKEN THAT LAMP IS FULLY COOLED BEFORE REIAMPING.
LENS
/-’___---
&
~ *. –
‘iv
.“--,,, -.,-.
w
I
FIG. 2
LAMP HOLDER
/, /“”
ASSEMBLY
“- -- PROJECTOR
ACCESSORY
NOTE: This framing projector accessory is for use on specific Llghtolier ~R16 fixtures only.
See fixture catalog for complete listing.
MR-16 FRAMING PROJECTOR ACCESSORY
lLLUMINAllON ON VERTKAL PLANE
ShutterBladesSetForMaximumBeamCoinage
-—
A) 30“ 4~ @ 30“ 45“ 60° 30“Q5:6@ 30“ 45“ 60“ 3~ 45:~ 3~5:_60: 30“ 45“ 60“
_Lennth(L) 16”22”44”27”37”70” 39_”_~l:97” 50”66”123-61” 81”150”72”95”176 84” l10”20Z’_
:IE:fzf-~=:7:E
FCWExw@?!lI?l_!? ‘l?I 61_20 65 34 11 3L20... ?_. 26 14 5. ~8__g0 ___3@ 7 2-———.-———
?sww14m~wc6811332 951234 119 37
— .- —————
E-..
b?ngth(L)to ttw pointthat FCdropsto 10%of maximum
12” 1~_2_~. 20” 30” 35” 29= 42” 4~ 37” 54” 62” 46” 66” 75” 54” 78” 88” 6~;—~fiijI~-”
_“~ ZO:_3~.”_5Y 26“ 44“ !B.: 33“ 55“ 83: 3.9= W “ AIZ:.Z7:_Llfj“152 “ ?8.”K.
I 117 61 20 70 37 12 4.? .?~_.8 ~3_ lg. !..i?j.ds!!jj
— -—.-.—.—
lLLUMINA~N ON HORIZONTALPLANE
—
—
Loading...