Lightolier OPT22400RL, OPT42400RL, OPT22400RL15, OPT42400RL15, OPT24000RL7 Installation Instructions Manual
...
RELAY MODULES
OPTIO RELAY MODULES
INSTALLATION INSTRUCTIONS
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR THE END USER. DO NOT DISCARD.
OPT22400RL - DUAL 2400W RELAY MODULE
OPT22400RL15 - DUAL 1800W RELAY MODULE
OPT42400RL - QUAD 2400W RELAY MODULE
OPT42400RL15 - QUAD 1800W RELAY MODULE
120VAC
FOR USE IN OPTIO LIGHTING CONTROL PANEL MODELS OPT3120, OPT6120, OPT9120
OPT24000RL7 - DUAL 4000W RELAY MODULE
OPT44000RL7 - QUAD 4000W RELAY MODULE
FOR USE IN OPTIO LIGHTING CONTROL PANEL MODELS OPT3277, OPT6277, OPT9277
277VAC
WARNING: Before installation, disconnect power at circuit breakers or remove fuse to avoid electrical
shock or damage to the unit. It is recommended that an electrician perform this installation.
THREE YEAR LIMITED WARRANTY
The Philips Controls product, when properly installed and under normal conditions of use (without overload, abuse or alteration), is warranted to you, the original user, for a period of three years form the date of
original retail purchase, to be free from defects in materials and workmanship. If during the warranty period you believe the purchased product or any part thereof has such a defect, you must return the product
(or part) at your cost during such period, with proof of purchase (or if installed by a third-party a written explanation of installation transaction with proof of date), to Philips Controls, 2828 Trade Center Dr. Ste.
130B, Carrollton, TX 75007, for repair or replacement (or to an authorized Philips Controls supplier which agrees in advance to handle the return and replacement by factory authorization). If the product or part
is found by Philips Controls to have been defective in material or workmanship it will be repaired or replaced (as deemed necessary by Philips Controls), and the replacement will be returned to you free of charge.
The original user is solely responsible for any costs associated with removal and re-installation of the product and shipping to Philips Controls or its authorized supplier.
PHILIPS CONTROLS LIMITS THE DURATION OF THE IMPLIED WARRANTY OF MERCHANTABILITY WITH RESPECT TO THE PRODUCT TO THE LIMITED WARRANTY PERIOD SET FORTH ABOVE, AND OTHERWISE
DISCLAIMS ALL IMPLIED WARRANTIES WITH RESPECT TO THE PRODUCT AND ITS PARTS. Some states disallow certain limitations on implied warranties so you should consult your state law if you have a questions
regarding this limitation and disclaimer. Philips Controls disclaims any and all liability for incidental, consequential, special or indirect damage arising out of any claimed breach of warranty or otherwise. However,
some states do not allow exclusion or limitation of such damages, so this disclaimer may not apply to you.
The remedy provided in the Limited Warranty for defective products is the user’s sole and exclusive remedy, subject to your state law. Further, this Warranty gives the user specific legal rights, and the user may also
have other rights which may vary from state to state.
If you believe warranty claim is warranted, you may contact your nearest authorized Philips Controls supplier. If one does not exist in your area, please contact Philips Controls Customer Service at the above address
(or at 1-800-526-2731), or please visit us at www.lolcontrols.com.
Made in U.S.A.
For technical/sales assistance, call: 1-800-526-2731
www.lolcontrols.com
P/N 85-6349A0
RELAY MODULES
www.lolcontrols.com
Note: The module will not operate properly if the shorting plug is left in circuit.
Note: The connectors of 277VAC Optio modules are keyed,
preventing the insertion of modules into panels of the incorrect voltage. Do not force modules
into slots.
Installation
Instructions
Description
The Optio Relay Modules offer economical and reliable switching of non-dim loads including
lighting, signs, and motors. The modules utilize rugged relays and feature dual-color status indicators, and focus buttons for manual operation and testing.
All Optio Dimmer Modules have identical mounting dimensions, allowing them to be easily
swapped within any of the Optio Lighting Control Panels. (Use caution to ensure that quad modules are not installed into spaces wired for dual modules.)
WARNING: Installing the module with power applied to the cabinet may expose you to
dangerous voltage and damage the device. Remove power before installing. A qualified
electrician should perform this installation.
Installation Procedure
Any combination of Optio dimming and relay modules may be installed in the Lighting Control
Panel. Blank covers MUST be installed in any unused spaces. Pull the jumper (shorting plugs)
before installing.
To install modules:
1. Unpack module and recycle or properly discard packaging materials. (Be sure to keep this
instruction sheet for future use.) Inspect relay module for signs of damage during transit.
2. Disconnect main power to Optio Lighting Control Panel.
3. Open relay module side of panel front cover.
4. If present, remove blank cover from location where module is to be installed (Figure 1).
When possible, lower modules should be installed first.
5. Remove shorting plugs from the load terminal block. (The shorting plug is the red tab protruding from the green load terminal block. To remove, grasp the shorting plug and gently
pull.)
6. Gently insert module into lighting control panel with the relays facing you. Secure module
using four screws (provided).
7. Close panel front cover.
Operation
Optio Relay Modules are
equipped with a "Focus Button" on
each circuit (Figure 1). Tapping
the focus button will turn the circuit
on, tapping it again will turn the circuit off.
Status LED Indications:
Red LED Green LED Condition
Off Off Normal
Off On
On Off Communication Error
Flashing Flashing Miswire to Line
Focus Mode
(controlled at module)
Figure 1: Installing Modules and Blank Covers
Screw (4)
Blank Cover
Screw (4)
Focus Button
& Status LEDs
NOTE: The Optio 9Module Panel is used to
illustrate the installation in
Figure 1. However, the
module installation is identical for all Lighting Control
Panel models.
Relay
Module
Load Terminal Block
Shorting
Plug
DETAIL
Terminal
Electrical Specifications
Operating Voltage: 120VAC, 50/60Hz
Number of Circuits:
OPT22400RL/OPT22400RL15: 2
OPT42400RL/OPT42400RL15: 4
Min Rated Load (Per circuit): 0.5W
Max Rated Load (Per circuit):
OPT22400RL: 2400 Watts
OPT22400RL15: 1800 Watts
OPT42400RL: 2400 Watts
OPT42400RL15: 1800 Watts
Operating Voltage: 277VAC, 60Hz
Number of Circuits:
OPT24000RL7: 2
OPT44000RL7: 4
Min. Rated Load (Per Circuit): .5W
Max Rated Load (Per Circuit):
OPT24000RL7: 4000W
OPT44000RL7: 4000W
Supported Load Types: Incandescent, Inductive, Magnetic Low
Voltage, Electronic Low Voltage, HID *
Cooling: Natural convection
Ambient Operating Temp: 0 to 40 degrees C
Relative Humidity: 5 to 95% (non-condensing)
Lightolier Controls
2828 Trade Center Drive • Suite 130B
Carrollton, Texas 75007
* When controlling HID lamps, derating of the relay circuit by 20%
is required.
For technical/sales assistance, call: 1-800-526-2731
Printed in U.S.A. ©Philips Controls 2007
P/N 85-6349A0
Loading...