Lightolier
45 INDUSTRIAL WAY, WILMINGTON, MA01887
LYTECEL LINEAR SURFACE/PENDANT AND ELECTRICAL FEED INSTRUCTIONS
NOTE: Fixture should be installed by a qualified electrician. Before installation, see dimensions.
1
Dimensions
Twist-on
Wirenuts
Remove Wireway Cover
to expose Wirenuts
for thru wiring
Wago Plug-in
Wirenuts
Twist-on
Wirenuts
Feed End
Feed End
Remove Wireway Cover
tp expose Wirenuts
for thru wiring
Wago Plug-in
Wirenuts
4'
Unit
8'
Unit
Continuous End
Continuous End
2
Slide Grip Hanger Assembly
End Or Middle of Row
Remove Louver by releasing four Spring-loaded
Latches. Remove Wireway Cover. Remove K.O.s
(2) from top of End Plate and install Slide Grip
Hanger into K.O. openings. Secure Slide Grip
Hanger to Fixture with Screw Provided. Feed
wires through opening in End Plate, into Wireway
Tab
End Cap
Screw Provided
Wireway
Cover
Ball
Chain
Louver
K.O.s
Slide
Grip
Hanger
Screw
Provided
Fixture
Screw
Provided
Screw
Provided
Slide
Grip
Hanger
Fixture
Wago
Plug-ins
8
Surface Mount Direct to Surface Without Slide
Grip Hanger
Insert Flexible Connector with at least 1/2" long
leads into wiring compartment and secure the
Flexible Connector with the Flexible Connector
Locknut. Mount the Fixture to the ceiling with
Mounting Screws (by others) or toggle bolts (not
supplied) through four 7/32" x 9/32" rectangular
holes. Make sure Fixture is mounted firmly and
the ceiling can withstand the weight of the Fixture.
Make electrical connections to Fixture, using twiston wirenuts provided. Re-install Wireway Cover,
install lamps (by others). Slip Ball Chain into key
slots in Wireway Cover and Install Louver.
Flexible
Connector
Wiring
Compartment
Flexible
Connector Locknut
Mounting
Screw
7
Assemble Slide Grip Hanger to Fixture as in
Step 2. Bring service leads from Outlet Box
through AC1 and Slide Grip Hanger, securing AC1
and Slide Grip Hanger to Outlet Box.
Outlet Box, Canopy, Slide Grip Hanger
Outlet
Box
© a Genlyte company 59-31135-000 Printed in U.S.A.
AC1
Slide Grip
Hanger
End
Plate
Fixture
K.O.'s (2)
and make wiring connections. If Fixture is to be
used as an individual, or mounting is to be at
joints, assemble Slide Grip Hanger to both ends of
1st Fixture.
Assemble End Cap to Fixture with Screws (2)
Provided at end of row. Install Wireway Cover and
Louver.
Lytecel 6-page Inst. Sht.qxd 2/25/05 4:40 PM Page 1
4
Cable Set for Continuous Row or End of Row with
Reflector or without Reflector
Secure cable set with threaded end of Mounting
Strap through Canopy into Top Cable Bushing.
Assemble Bottom Cable Bushing to Slide Grip
Hanger with Nut as shown. Assemble Strain Relief in
K.O. in Slide Grip Hanger and seat properly. Use
Screws to assemble End Cap to Fixture. Bend tabs
out to secure Slide Grip Hanger to Fixture when not
installed at end of Fixture.
Catalog No. WC60 – Canopy, Cable
Catalog No. WCC60 – Canopy, Cable, Straight Cord
Catalog No. WCCC60 – Canopy, Cable, Coiled Cord
Strain
Relief
Tab Detail
Mounting
Strap
Canopy
Top Cable
Bushing
Fixture Side Rail
Bottom
Cable
Bushing
Slide Grip
Hanger
Bottom
Cable
Bushing
Strain
Relief
Detail
Slide Grip
Hanger
Fixture
Side Rail
Strain Relief
Nut
Mounting
Strap
Canopy
Strain
Relief
Strain
Relief
Detail
Top Cable
Bushing
Fixture
Side
Rail
Bottom Cable Bushing
Slide Grip
Hanger
Fixture
End Cap
Nut
Strain
Relief
Screw
Strain Relief
(8') 99-3/4"
(4') 48"
Slide Grip Hanger Along Length of Fixture
Slide Grip Hanger for Beginning or End of Row
3
Stem Set for End of Row or Continuous Row
Mounting with Reflector or without Reflector.
Slip threaded end of stem through Canopy. Attach
Stem(s) to Slide Grip Hanger using Nuts as shown.
Assemble Slide Grip Hanger to Fixture Slide Rails.
Assemble Ball Aligner to Stem and Slide onto
Mounting Strap.
For sloped ceilings, be sure opening of Mounting
Strap is positioned facing upward with the slope of
the ceiling or Stem will disengage.
Bend Tab out to secure Slide Grip Hanger to
Fixture when not installed at end of Fixture. Make
wiring connections. Using Screws, secure End Cap
to Fixture.
Canopy
Canopy
Stem
Stem
Nut
Nut
Slide Grip
Hanger
Slide Grip
Hanger
Nut
Nut
Fixture
Side Rail
Fixture
Side Rail
Tab Detail
Slide Grip
Hanger
Nut
Stem
Mounting
Strap
Ball Aligner
Ball Aligner
Mounting
Strap
Nut
Slide Grip
Hanger
Fixture
End Cap
(8') 99-3/4"
(4') 48"
Screw
Slide Grip Hanger Along Length of Fixture
Slide Grip Hanger for Beginning or End of Row
5
Slide Grip Hanger Mounting Locations
12" (305mm)
Max. 4' Unit
24" (610mm)
Max 8' Unit
12" (305mm)
Max. 4' Unit
24" (610mm)
Max 8' Unit
6
Join Fixtures with Screws (2) Provided. Hook
wires into Slot in End Plate. Make Plug-in wiring
connections in Wireway. Replace Wireway Cover.
Through Wiring/Continuous Rows
Fixture
Screw
Provided
Screw
Provided
Wago
Plug-ins
Supplied
#14 Gauge
Maximum Wire
Solid or Stranded
Slot
Alignment
Tab
End Plate
48" (1219mm) or 96" (2439mm)
42" (1067mm) or 90" (2286mm)
3" (76mm) Min.
3" (76mm) Min.
Lytecel 6-page Inst. Sht.qxd 2/25/05 4:40 PM Page 2
Loading...