Lightolier IS-T300 User Manual

INSTRUCTION SHEET

IST:300

09-01/Rev-03

INSTALLATION INSTRUCTIONS FOR MR-16/ES16 TRIM IN PRE-WIRED

INCANDESCENT 12V OR 120V MOUNTING FRAME

ATTENTION: Read and understand these instructions before installing fixture. This fixture is intended for installation in accordance with the National
Electrical Code or Canadian Electrical Code (if applicable) and local regulations.To ensure full compliance with local codes and regulations, check with your
local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding. Retain these instructions for

maintenance reference.

Note: For the 50W IC frame-in kit

Put down the
onto the

lamp shield (included with the IC frame-in kit)

lamp. (Fig.1)

A. LAMP:

1.

MR16: Insert the pins of the lamp base into the socket.
(Fig.2)

2.

ES16: Insert the pins of the lamp base into the socket.
and rotate the lamp clockwise. (Fig.2A)

3. Turn the

lamp under spring (if applicable). (Fig.3,4,5)

CAUTION: Lamp manufacturer recommends that the
protective glass be in place before energizing the
lamp. Insure that the lamp is fully cooled before
relamping.

B. TRIM: Standard (Model 305)

1. Push the

trim into the housing. (Fig.6)

2. Aim the lamp beam at the desired angle if necessary.
(Fig.12)

C. TRIM: Adjustable pinhole (Model 308)

1. Push the

trim into the housing. (Fig.7)

2. Gently rotate the trim to fit it to the ceiling.

3. Aim the lamp beam at the desired angle if necessary.
(Fig.11)

D. TRIM: Glass (Model 322)

1. Take the

loop found at the end of the security cable

attached to the

trim and secure by passing the loop

over either one of the screws found within the

housing.

(Fig. 8)

2. Push the

trim into the housing. (Fig.8)

3. Gently rotate the trim to fit it to the ceiling.

E. TRIM: Adjustable elbow (Model 478)

1. Push the

trim into the housing ,compressing the (2)

springs as shown. (Fig.9)

F. TRIM: Wall Washer (Model 315)

1. Push the

trim into the housing and position the lamp

shield as shown. (Fig.10)

2. Push the

trim into the housing and position the lamp

shield as shown. (Fig.10)

Wall Washer:

1. Position the fixture a minimum of 12 away from the
wall. (Fig.10)

2. Adjust the angle of the
using the

frosted glass. (Fig.9)

beam towards the baffle by

Accent Lighting:

1. Adjust the angle of the beam to the required position
by using the

clear glass.

G. ES16 TRIM: (Models 325, 330)

1. Install the

spring tabs into the slots in the base.

(Fig.11)

2. Insert the

pins of the lamp base into the socket.

and rotate the lamp clockwise. (Fig.2, 2A)

3. Push the

trim into the housing. (Fig.12)

4. Aim the lamp beam at the desired angle if necessary.
(Fig.12)

H. TRIM: Contour (Model 316)

1. For added protection in shower application , install the
gasket for water-tightness (included). Gently fasten
onto the

trim. (Fig.13)

I. MAINTENANCE of ALZAK® REFLECTORS OR

ALZAK® CONES: (if applicable)

Note: Handle the reflector or the Alzak® cone with
clean gloves or plastic film to avoid fingerprints.

1. Clean Alzak® surfaces with a clean soft cloth
dampened in a mild detergent solution.

2. Rinse then wipe dry with a dry cloth or a paper towel.
Avoid abrasives.

Model 322

TRIM

PROTECTIVE

TRIM

HOUSING

SPRINGS

FIG.9

SOCKET

PINS

LAMP

SPRING

GLASS

LAMP

Model 308

Model 315

TRIM

LAMP

SHIELD

LAMP

FIG.1

LAMP

FIG.2A FIG.3

FIG.4

Model 305

HOUSING

TRIM

FIG.6

Model 478

LOOP

HOUSING

SECURITY
CABLE

FIG.8 FIG.10

Model 325,330

SPRING
TABS

SLOTS

FIG.11

GASKET

TRIM

TRIM

FIG.13

FIG.2

LAMP

SPRING

FIG.5

HOUSING

FIG.7

HOUSING

WALL

SHIELD

HOUSING

FIG.12