Lightolier IS-6079 User Manual

r

‘“WERF’”’N

$

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

Thisfixtureisintended forinstallationinaccordancewiththeNational

To assure full compliancewithlocalcodesandregulations,checkwithyourlocalelectricalinspector

installation. Toprevent electrical shock, turnoff electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTALLATION FOR AITACHING EXTENSION WAND SLOPED CEILINGS ADAPTER

TO LYTESPAN TRACK. FOR USE WITH LYTESPAN” TRACK SYSTEMS ONLY

Extensionwandslopedceilingadaptercanbe mountedonanyBasic,Advent Multipointor MonopointTrackon tailingsfrom 0° to 90° (vertical).

Notfor usewith Lytespota withattachmentfitting7589.

Grasp TOP FITTING at top of ADAPTER and insert it into the LYTESPAN TRACK. The LOCKING LEVER must be on the same side of the track as the BEAD.

1.

(see Fig. 1.)

2. Rotate the TOP FI’ITING W’ clockwise, (See Fig. 2), untilLOCKING LEVER snaps and locks in plats. (See Fig. 3.) Do not rotate adapter from LOWER FllllNG.

3. Loosen KNOB and set the lower haff of the ADAPTER to a vertical positionand tighten KNOB. (Fig, 4)

4. To Remove Depress LOCKING LEVER; then rotate TOP FllllNG 90° counter-dockwke. Do not rotate wand from LOWER FITTING,

Electrical Code and load regulations.

before

INSTRUCTION SHEET NO.

IS:6079

0493

Page 1 of 2

LVTESPAN

TRACK

BEAD

FITTING

L

!l-

LOCKING

LEVER

FIG. 1

INSTRUCTIONS

2 CIRCUIT TRACK SYSTEMS

See Fig.5, BRASS CONTACT can beraisedorlowered,Brokenlineindicatespositionfor1 circuit
trackor lowercircuitof2 circuittracksystem.

To mnverf attachment FllTING for upper circuitof2 circJJittrack, raise BRASS CONTACT to high
positionby Ming CONTACT as high as stop f.wrnits and CONTACT clicks into place.

INSTRUCTIONS FOR AllACHING EXTENSION WAND TO EXTENSION WAND SLOPED CEILING ADAPTER

Insert the WAND FllllNG into the LOWER FllllNG.

1.

The LOCKING LEVER must be on the same side as the bead located at the bottom of the LOWER FllTING (See Fig. 6.) Rotate the WAND FllllNG
90° clockwise until LOCKING LEVER snaps and locks in place. (See Fig. 6,7, & 8).

2, To remove, depress LOCKING LEVER and rotate FllllNG 90° counterclockwise.

FOR CONVERTING FITTING TO OPERATE ON

c

CLOCKWISE

-u

FIG. 2

ri

FIG. 3

FIG. 4

BRASS CONTACT

L::;;:G

FIG. 5

NG

I I

I

/-R/la

BEAD BRASSCONTACT

LOCKING_

LEVER

“OWN

_ WAND

FllTNG

1

FIG. 6

CLOCKWISE

FIG. 7

i

FIG. 8

*

-

INSTRUCTION SHEET NO.

1s:6079

0493 Page 2of 2

INSTALLATION FOR AITACHING EXTENSION WAND SLOPED

CEILINGS ADAPTER TO LYTESPAN TRACK. FOR USE WITH

LYTESPAN@TRACK SYSTEMS ONLY (Continued)

INSTRUCTIONSFORAllACHING LYTESPOV FIXTURESWITHSQUATADAPTERTOWANDSLOPEDCEILINGADAPTER

1. InserttheFIXTUREFllllNG intotheWANDSOCKET.
TheLOCKINGLEVERmustbeonthesamesideasthebeadlocatedatthebottomofthewand(SaaFig.9.)RotatetheFIXTUREFITTING90°clockwise
untilLOCKINGLEVERsnapsandlocksintoplace.(SeeFig.9,10,&11).

To remove, depress LOCKING LEVER and rotate FllllNG 90° counterdockvke,

2.

=f&icL- ‘Go kFIG.ll

INSTRUCTIONS FOR AllACHING

1, Insert the FIXTURE FllllNG intothe WAND SOCKET.

The LOCKING LEVER must be on the same side as the bead located at the bottom of the WAND SOCKET (See Fig. 8.) Rotate the FIXTURE
FllllNG 90° clockwise. (See Fig. 12, 13, & 14).

2, To remove, rotate FITTING 90° counterclockwise.

LOW VOLTAGE LYTESPO~ TO WAND SLOPED CEILING ADAPTER

WAND

SOCKET

BEAO

~

LCCKING-

LEVER

\

INSTRUCTIONS FOR A~ACHING LYTESPOT WITH “T” ADAPTOR TO WAND SLOPED CEILING ADAPTER

1. Align BEAD on WAND SOCKET with GROOVE in FITTING before inserting into WAND SOCKET, see Fig. 15. (If BEAD is

n

%

@

t~

FIXTURE

FITTING

/’

FIG. 12

CLOCKWISE

(--’

FIG. 13

r--?

1

\ \

FIG. 14

NOT aligned

a potential hazard may result.)

2, Poshion LEVER as shown in Fig. 15.

3. Insert FllllNG into WAND SOCKET, Turn LEVER 90° to make mechanical and electrical connection, See Fig. 16.
4, To remove reverse procedure.

NOTE: If “T” ADAPTOR has a full gasket on top, remove 1/2” strip of cork between contact hub and grounding spring, If there is no

gasket, and a tighter fti to the WAND is desired, remove backing from enclosed GASKET. When centered on FllllNG apply pressure
on GASKET to secure it.

WANO

SCCKET

-._—————

CONTACTHUB
GROUNDINGSPRING

BEAD _

~~- - GRouND, ‘:-~ ‘WK

GASKET ~

GROOVE

1

FllllNG

$ “ ‘4

FIG. 15

REMOVECORKAND
PAINT(IFPRESENT)
FROMTHISAREA
TO INSUREPROPER

\

LEVER

FIG. 16

RELEASE

FIG. 17