Lightolier IS-6074 User Manual
I
EiHy!ii&y&&
P
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
Thisfixture is intended
To assure full complianm with local codes and regulations, check with your local electrical inspector before
installation. Toprevent electrical shock, turnoff electricity at fuse box before proceeding.
for installation in accordance with the National Electrical Code and local regulations.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:6074
ROI 93
Page 1 of 2
INSTALLATION FOR AITACHING EXTENSION WAND TO LYTESPAN TRACK
FOR USE WITH LYTESPAN@TRACK SYSTEMS ONLY
Lytespot extension wand can be mounted on any Basic, Advent, Multipoint or Monopoint Track. It is intended for insulation on level ceilings only. Do not
mount on slope ceilings or walls unless when used with extension wand sloped ceiling adapter (6079WH, BK) ordered separately. Will fit Lytespot fixtures
with Squat Adaptors, Low Voltage Adapters and Standard “T” Adaptors. NOTE: Do not exert sideward pressure on fixture,
NOTE: This Extension Wand is equipped with a flex joint to prevent damage by accidental impact. Heavy asymetric lighting equipment
should NOT BE used on this
1.Grasp FllllNG at top of EXTENSION WAND and insert it into the LYTESPAN TRACK. The LOCKING LEVER must be on the same side of the track as the BEAD,
(See Fig. 1.)
2. Rotate the top FITTING 90° clockwise, )See Fig. 2), until LOCKING LEVER snaps and locks in place. (See Fig. 3.) Do not rotate wand from STEM or
BOllOM HOUSING,
3. To Remove: Depress LOCKING LEVER; then rotate TOP FITTING 90° counter-clockwise. Do not rotate wand from STEM or BOITOM HOUSING,
BEAD
device.
LYTESPAN
TRACK
FITTING
5
LOCKING
LEVER
.1
INSTRUCTIONS FOR CONVERTING Fll_llNG TO OPERATE ON
2 CIRCUIT TRACK SYSTEMS
See Fig.4. BRASS CONTACT can beraised orlowered, Broken line indicates position for 1 circuit
or lower circuit of 2 circuit track system.
track
To convert attachment
position by lifting CONTACT
INSTRUCTIONS FOR AllACHING LYTESPOW FIXTURES USING SQUAT ADAPTER TO BOllOM OF LYTESPAN@ WAND
Insert the FIXTURE FITTING into the WAND SOCKET,
1.
The LOCKING LEVER must start on the same side as the bead located at the bottom of the wand (See Fig. 5.) Rotate the FIXTURE FITTING 90° clockwise
until LOCKING LEVER snaps and Iockd into place. (See Fig, 5,6, & 7).
2. To remove, depress LOCKING LEVER and rotate FllllNG 90° counterclockwise,
FllTING for upper circuit of 2 circuit track, raise BRASS CONTACT to high
as high as stop permits and CONTACT clicks into place. FIG. 4
BEAD
CLO
IG. 2
BRASS CONTACT
BRASS CONTACT
LOCKING
LEVER
Lf~;~RG ~
\
a
/
k,
CAUTION: SUPPORT THE LOWER WAND HOUSING WHENEVER MANIPULATING THE FIXTURE.
B. I <5 n-l
7-<>L IE R“
I
v
INSTRUCTION SHEET NO.
INSTALLATION FOR AITACHING EXTENSION WAND TO
1S:6074
RO193 Page 2 of 2
INSTRUCTIONS FOR ATTACHING LOW VOLTAGE LYTESPOT TO LYTESPAN” WAND
insert the FIXTURE FITTING into the WAND SOCKET,
1,
The LOCKING LEVER must start on the same side as the bead located at the bottom of the WAND SOCKET (See Fig. 8,) Rotate the FIXTURE
FllliNG 90° clockwise. (See Fig. 8,9, & 10),
2. To remove, rotate FllllNG 90° counterclockwise,
FOR USE WITH LYTESPAN@TRACK SYSTEMS ONLY (Cent’d)
LYTESPAN TRACK
—
.
WAND –
SOCKET
BEAD
IMPRG _
( @
t\
FIG. 8
INSTRUCTIONS
Align BEAD on WAND SOCKET with GROOVE in FITTING before inserting into WAND SOCKET, see Fig. 11, (BEAD is NOT aligned
1.
a potential hazard may result,)
2, Position LEVER as shown in Fig. 11.
3, Insert FllTING into WAND SOCKET. Turn LEVER 90° to make mechanical and electrical connection. See Fig. 12.
4. To remove: reverse procedure.
FOR AllACHING LYTESPOF WITH “T” ADAPTOR TO LYTESPAN@ WAND
CLOCKWISE
{
r-l
m
FIG. 9
f“ 1
n
\
FIG. 10
CONTACT HUB
GROUNDING SPRING
REMOVE CORK AND
PAINT (IF PRESENT)
FROM THIS AREA
;\t:;UDIE PROPER
LEVER
._ ————
FIG. 12
=... LOCK
-.-J
3
RELEASE
FIG. 13
GASKET
WAND
SOCKET
BEAD _
*
GROOVE
FITTING
.._~
-“
-“
1
‘4
$
\
FIG. 11
NOTE:If “T” ADAPTOR has a full gasket on top, remove 1/2” strip of cork between contact hub and grounding spring. If there is no
gasket, and a tighter fit to the WAND is desired, remove backing from enclosed GASKET. When centered on FllllNG apply pressure
on GASKET to secure it.
\
Loading...