Lightolier IS-5453 User Manual

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
his fiXtIIrO
!gulations.To assure full mmpliansa with Iosal rndes and regulations, shesk with your local elestrissl
lspestorbefore installation. To prevent elestrisal shosfr,tum ofi eleatdsity at fuse box before prmeeding.

k intendedfor installationin acmrdsnca with the NationalEbafrisalCode and IOCA

Retain Iheae instructions for maintenance reference.

INSTRUCTIONS FOR INSTALLATION OF 5453

INSTRUCTION SHEET NO.

IS:5453

1291

CAUTION

FOR OCTAGONALOUTLETBOXES
. Position BACKPWTE ASSEMBLY centered over OUTLET BOX with bottom edge of BACKPLATE in fine with bottom of OUTLET SOX. (Fig. 1).

Using all MOUNTING HOLESin BACKPL4TEASSEMBLY, semretowallusingwood stiews,toggleklts, oralternatefasteners (not provided) depending

on WSIImaterial. NOTE BACKPLATE ASSEMBLY should be leveled horizontally and outlet box completely covered before final tightening to wall.

‘OR HORIZONTALLY MOUNTED RECTANGULAR GEMOR SWITCHOUTLETBOXES

. Remove COVER PIATE horn BACKPLATE ASSEMBLY aa shown in Fig 3.

:,Position BACKPIATE ASSEMBLY centered over OUTLET BOX with bottom edge of BACKPMTE in line with botiom of OUTLET BOX.(Fig. 2).
. Uaingall MOUNTING HOLES inBACKPIATEASSEMBLY, aecuretowall using woodaixews, toggle bolta,oralternatefasteners (notprovided) depending

on wall material.

NOTE BACKPUTE ASSEMBLY should be leveled horizontally and outlet box completely covered before final tightening to wall.

VIRING PROCEDURE

. Pull supply wires through WIREWAY OPENING and make conneofions

Blaak fixture lead (or fixture lead without tramr mark) to black supply Ieact white fixture lead (or fixture lead with tracer mark) to white supply wire.
Uninaulstad wire is a GROUND WIRE and must bernnneciad to agroundkrgtarminal or ground wire inthe OUTLET SOX, Use wire nuts (local hardware
item), Push the”splisea into the OUTLET BOX.

!,Raiae, FIXTURE ASSEMBLY and align MOUNTING STUD HOLES and SOCKET HOLES with SOCKETS and MOUNT STUDS on BACKPMTE. Gently

slide FIXTURE ASSEMBLY backwards until the MOUNTINGSTUDSprotrudethroughtheholesin FIXTUREASSEMBLY,Securein placewith
BAITERY NUTS provided.
CAUTION: MAKE CERTAIN THAT NO WIRES ARE PINCHED BETWEEN THE BACKPlATE ASSEMBLY AND THE FIXTURE ASSEMBLY.

1.From top of fixture, position DIFFUSER DISHES over shsular openings (ss shown in Fig. 4) and gently lower until dishes sit securely in each opening.
i. Cover INSPECTION WINOOW with INSPECTION COVER PLATE and secure with screws (Fig. 4).
i. Install remmmended lamps.

CAUTION MAXIMUM WAllAGE AS MARKED ON FIXTURE MUST NOT BE EXCEEDED. FOR HORIZONTAL MOUNTING ONLY.

DO NOT MOUNT TOP EDGE OF FIXTiJRE CLOSER THAN 6 INCHES TO CEILING.

WIREVAAYOPENING

}0

=ig. 1

WIREWAYOPENING>

:0

o Oo

WTAGONAL BOx~ L eACKPIATEASSEMaLY

000;

w

Fig.3

GEMaOX~

=

Front View

VI’4

------ ~TE

:000.:

~:o o

~ BACKPlATEASSEMaLY

WIREW,AY OPENING

MOUNTINGHOLE~

ouTLETsox COVERPLATE--J

1

1A

::= V-BA”ERYNUTS

\-

- OiRWSER