Lightolier IS-4A28442 User Manual
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electric al inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:4A28442
A0501
Page 1 of 2
INSTRUCTIONS FOR INSTALLATION OF PENDALUX PENDANT SERIES
Note: This instruction sheet covers several luminaire (fi xture) styles. Although suspension, chassis, lamp type and diffus er may vary from that shown,
installation is the same.
SWI VEL BALL
INSTALLATION (Fig. 1):
1. After opening carton and removing top packaging material,
allow CHASSIS to remain in carton for protection.
2. Assemble SUSPENSION system following the appropriate
instructions outlined below.
Suspension Assembly:
Single Stem Suspensions (4 SB1 Se rie s):
1. If no extension kit is to be used; cut three wires (BLACK,
WHITE and GREEN) no less than 6” above SWIVEL BALL.
Strip back insulation from each wire approximately 3/8” from
each end (Fig. 1).
2. If an extension kit is to be used, follow instructions provided
with extension kit.
Multi-Stem, Contemporary and Traditional 3-Arm
Suspensions (4SB2, 4SB3 & 4SB4 Seri es) :
1. If no extension kit is to be used; cut three wires (BLACK,
WHITE and GREEN) no less than 6” above SWIVEL BALL.
Strip back insulation from each wire approximately 3/8” from
each end (Fig. 1).
2. If extension kit is not to be used, thread UPPER STEM into
THREAD ADAPTOR until tight (Fig. 1).
3. Using ALLEN WRENCH provided tighten two SET SCREWS
in the sides of THREADED ADAPTOR securing UPPER
STEM in position.
4. Cut three wires (BLACK, WHITE and GREEN) no less than 6”
above SWIVEL BALL. Strip back insulation from each wire
approximately 3/8” from each end (Fig. 1).
5. If an extension kit is to be used, follow instructions provided
with extension kit.
NOTE: For the Traditional 3-Arm suspensions, the upper half
of COLLECTOR BALL can be pulled upward to gain access
to THREADED ADAPTOR (Fig. 8).
Suspension Installation:
1. Position SUSPENSION next to CHASSIS and insert MALE
CONNECTOR from SUSPENSION into FEMALE
CONNECTOR and snap together.
2. Pass RED WIRE from CHASSIS up through CENTER PIPE
on SUSPENSION.
3. If necessary, cut and strip back insulation on RED WIRE as
done in step one under suspension assembly above.
4. Loosen three SCREWS on the top of CHASSIS as shown in
fig. 1.
5. Position KEYSLOTS in SUSPENSION PLATE over three
SCREWS on top of CHASSIS (Fig. 1).
6. Twist SUSPENSION PLATE clockwise allowing three
SCREW HEADS to pass over BUMPS on the sides of
KEYSLOTS.
7. Secure SUSPENSION in place by fully tightening three
SCREWS.
CAUTION: USE LAMP WATTAGE AND TYPE AS
MARKED ON LUMINAIRE
SUSPENSIO N PLATE
RED WI RE
SCREW
GREEN WI RES
WHITE W I RES
BUMP
SCREWHEAD
KEYSLOT
RED WI RE
SUSPENSION
MAL E CONNECT OR
FIG. 2
BLA CK WI RES
FIG. 3
FEM ALE
CONNECTOR
CHASSIS
FIG. 1
A
COMPANY
631 Airport Road, Fall River, MA 02720
INSTRUCTION SHEET NO.
IS:4A28442
A0501
Page 2 of 2
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electric al i nspect or before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
Final Installation:
1. If a SUPPORT PLATE is provided (Fig. 4), drop CROSSBAR
down into SUPPORT PLATE as shown.
2. Using appropriate slots in CROSSBAR, secure CROSSBAR
and SUPPORT PLATE to OUTLET BOX using OUTLET BOX
SCREWS (provided with outlet box).
3. If SUPPORT PLATE is being used, secure SUPPORT PLATE
directly to ceiling surface using four MOUNTING HOLES. Use
appropriate fasteners for the type of ceiling (i.e. wood screws,
molly bolts, etc.).
CAUTION: Luminaire may weigh up to 40 lbs.
Always use Support Plate (when provided) with
the appropriate mounting hardware.
4. Slide CANOPY over the SWIVEL BALL (Fig. 6).
5. Raise CHASSIS and SUSPENSION assembly to CROSS
BAR. Position SWIVEL BALL through the opening in the end
of the CROSSBAR as shown in Fig.5.
6. Allow SWIVEL BALL to rest down inside the CROSS BAR
making certain the TAB on CROSSBAR is aligned with slot in
SWIVEL BALL.
Wiring Luminaire:
Conventional Wiring (all lamps on, single switch):
1. Make connections: BLACK and RED luminaire leads to hot
supply lead; white luminaire lead to neutral (white) supply
lead. Green luminaire lead is a ground wire and must be
connected to grounding terminal or ground lead inside
OUTLET BOX. Use WIRE NUTS (local hardware item). Push
supply wires and connections back into OUTLET BOX.
Multi-Level Wiring (all lamps on or only two lamps
on, two switches):
Note: Requires two separately switched hot supply leads.
Option not available on two lamp units.
1. Make connections: BLACK luminaire lead to first hot supply
lead; RED luminaire lead to second hot supply lead; white
luminaire lead to neutral (white) supply lead. Green luminaire
lead is a ground wire and must be connected to grounding
terminal or ground lead inside OUTLET BOX. Use WIRE
NUTS (local hardware item). Push supply wires and
connections back into OUTLET BOX.
2. Snap CROSSBAR CLIP onto CROSSBAR as shown in Fig. 5
and secure CLIP in place by tightening CLIP SCREW.
Canopy Installation:
1. Slide CANOPY up STEM aligning SLOTS in INNER CANOPY
with SCREWS protruding from CROSSBAR (Fig. 6).
2. Rotate CANOPY clockwise until CANOPY snaps securely
against ceiling.
3. Install recommended lamps
Final Suspension Assembly:
Traditional 3-Arm Suspensions
1. Pass un-threaded end of ROD up into hole in side of
COLLECTOR (Fig. 8). Secure in position by threading ROD
into SWIVEL BRACKET (Fig. 7). Repeat for remaining
RODS.
Contemporary 3-Cable Suspensions
1. Thread PLUNGER into SWIVEL BRACKET
2. Push end of CABLE through PLUNGER opening until CABLE
is tight (Fig. 9). Repeat for remaining CABLES.
SWIVEL
BRACKET
CABLE
OUTER
DIFFUSER
SUPPORT
CAP
PLUNGER
FIG. 9
OUTLET BOX
CANOPY
DECORATIVE
KNOB
COLLECTOR
CROSSBAR
CLIP
SWIVEL
BALL
SWIVEL
BRACKET
WIRE NUT
OUTLET BOX
SCREWS
SUPPORT
PLATE
AUXILIARY
FASTENING
HARDWARE
FIG. 4
CROSSBAR
CROSS BAR
SCREW
CLIP SCREW
FIG. 5
SCREW
INNER
CANOPY
CANOPY
FIG. 6
FIG. 7
ROD
FIG. 8
A
COMPANY
631 Airport Road, Fall River, MA 02720
Loading...