Lightolier IS-44224 User Manual
~ READ AND UNDERSTAND THESE lNSTRUCTIONS EEFOREINSTALLING H~URE INSTRUCTION SHEET NO.
This fixture is intended for installation in
‘regulations.To
‘inspector before installation. To preven!eiecticaf shock,turn oft electtaty atfuse box~fore proceeding.
.-.
I
>
assurefull@mpiiancewithlocalcodesandregulations,rne& withyourlocalelectical
Retain these instructions for maintenance reference. .
...... .,-.’ --
.,.
—-
-----——-———..— ..._——
COVERS ALL MINI-BRACELET FIXTURE SERIES
accordance wirh the NationaJ Electrical Code and local
....’
-INSTRUCTIONS FOR INSTALLATION
r
IS:44224
, .- ..’:...,.:; .. . .
1094
.-
. —.
PAGE +’OF .2 .~
. ..
... ..-,— —
-1
1
-,
,.
PREPARE FIXTURE FOR INSTfifiTION: Remove “CAPSCREWS that secure COVER
PLATE to BACKPLATE ASSEMBLY.
,
Remove .COVER PLATE and set aside.
FOR OCTAGONAL OUTLET BOX MOUNTING: ‘
1. -Attach OUTLET BOX COVER to BACKPLATE ASSEMBLY using the two pro: vialed screws (see figure 1) .
2~,Wiring procedure:
while supporting””BACKPLATE ASSEMBLY make “ :
,;,’connections:Black fixture lead (or fixture lead without tracer
.“...’mark)toBlack supply lead; White fixture lead (or fixture lead
.,.-,,
with tracer mark)to White supply lead. Uninsulatedwire is a
...
GROUND WIP.E and it must be connected to a-g-r”ounding terminal or
ground wire in the OUTLET BOX.
Use wirenuts (local hardware item)
push the splices into the OUTLET BOX. Make certain that wires are
not pinched between BACKPLATE ASSEMBLY and wall (see figure 1) .
-WARNING-RISK OF FIRE. MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY
WIRE RATED 60”DEGREE ”C.CONSULT A QUALIFIED ELECTRICIAN BEFORE ‘
INSTALLATION .“
-WHEN MOUNTING
HORIZONTALLY, USE SUPPLY WIRE RATED FOR AT LEAST 60
DEGREE C.
-WHEN MOUNTING
:DEGREE C.
....- .-.
Vertically,
USE SUPPLY WIRE RATED FOR AT LEAST 75
-.. . .. -
%’IR’ENUTS
/
(NoT SUPPLIZD)
& Aw -
..
.-
BACKPMTE ASSEM3LY
OCTAGONAL OUTIIT BOX~
.
COVER PIATE-”
ENO COVER (WITH ONE CLOSED END)
,.
=%w /
7
‘L’’/2-2.
@ilK
‘v-’
‘@
/
-.
A
–FIGURE l–
.“t
lNSTMLTHiS EWE UP WHEN
UCWTINGWTURCH3RIZOKWLLY
[ . [~sTRLJcTloNsj+EETNoo I
—.-. — L— . . .
OCIAGONAL OUTLET BOX y
~OUTLZT BOX COb’ER
IIS:$44224, ,
“io94
,_.
,, ,..
pcsition BACKpLATE AS S~BLY centered over OUTLET BOX. Use a leVel
3.
placed on top of fixture. Once fixture is level, use MOUNTING
HOLES as a template and mark drill locations (see figure 2) .
Usin~ all MOUNTING HOLES in BACKPLATE ASSEMBLY, secure to wall
.4.
using wood screws, toggle bolts,
vided) depending on wall material. Note: care must be taken to
insure that OUTLET BOX is completely covered.
F.OR HORIZONTALLY MOUNTED RECTANGULAR GEM OR SWITCH OUTLET BOXES:
1. Make,wiring connections per instruction provided in’istep 211above.
PositIon BACKPLATE ASSEMBLY per instruction provided in’lstep 3’1.
2.
Mount BACKPLATE ASSEMBLY per instruction provided inf’step 4“
3.
above.. Note:
outlet box must be also installed vertically.
COVERI?LATE MOUNTING PROCEDURE:
1;. Remcve THREADED KNOBS that secure END COVERS to COVER PLATE. Re-
mcve END COVERS and set aside with THREADED KNOBS.
2; Install COVER PLATE onto THREADED STUDS (pressing firmly to
compress the GROUNDING CLIP) on BACKP’LATE ASSZMBLY. ~se_ extreme
!
I
I
care to not pinch wires between parts. (Note: when installing fixture horizontally, observe
to insure proper orientation).
ASSEMBLY by threading CAPSCREWS anto MOUNTING STU9S(see figure 1)
3. Install recommen~ed lamps. Caution:
f~xture must not be exceeded.
GLASS DIFFUSER INSTALLATION:
1. Position GLASS DIFFUSER as shown in figure 3, step 1.
2. Move GLASS DIFFUSER towards COVER PLATE until UPPER and LOWER
TABS on GLASS DIFFUSER touch COVER PLATE (see figure 3, step 2) .
Gently slide GLASS DIFFUDER in a downward direction until UPPER
3.
TABS fullv en~aae into HOLDER BRACKETS (see fiqure 3, step 3) .
While sup~ort~n~ GLASS DIFFUSER,
4.
STUD on COVER PLATE.
KNOB onto THREADED STUD. Note:
one side are used on either end of fixture to close-off the _
HOLDER BRACKETS on the very ends (see figure 3, step 3) ..
—-------...—
PAGE 2 OF 2
..——. .—
1
o
.—
where fixture is mounted vertically, gem or switch
—
/
/’
/
LOWER
.TABS
BACKPLATE”
ASSf MBLY
1
MOUNTING
HOLCS
~AcKpuTE , -. . . . .
AS LCUSLYr ---
Secure END COVERS by installing THREADED
.
‘m–—-––-’-”” ““” - —
w
7
+$
i*\
“f
I
)
VII
‘“-
GLASS
OIFFUSZR
L<-
o“
.
o
1
CfU/SWITCH OUTLET BOX - \
0
.
0
or alternate fasteners (not pro-
llTHIS EDGE UP” marking on COVERP-LATE
Secure COVER PLATE to BACKPLATE
maximum wattage marked on the
install END COVERS onto THREADED
ENDCOVERS that are closed-off on
r--
COVER PLATE
I
\
\
. ~—. ..— ..—
~~lGUR~ Z<i
CD
——-
.-. —- . . ..
HOLDER BRACKCT
“/
—
,—
B<
0
.
0
ENO COVER
THREAOED.
KNOB
.
i’,
–FIGURE 3–
Loading...