Lightolier IS-40714 User Manual

READAND UNDERSTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFIXILfRE

tisfixiure is intended for installation inaccordancewiththeNefionalElectricalCodeandlocalregulations.
Jassurefullcomplianm with local codes and regulations, check with your Iocd electrical inapecfor before

stallation. To prevent elestrfcal shock, turn oft elecfriufy at fuse box before proceeding.

Retainthese inatructiona for maintenancereference.

INSTRUCTIONS FOR INSTALLATION OF TRADITIONAL STYLE RADIANCE PENDANTS

‘[XTUREASSEMBLYAND INSTALLATION:

1. CarefullyremoveCENTERSTEMASSEMBLYfrompackaging.

2. UnscrewKNURLED

3. Mount CROSSBAR and CENTER STEM ASSEMBLY/CHAIN to OUTLET BOX using OUTLET BOX SCREWS (provided with outlet box).
4, Make electrica ccfnnections black ftiure lead or fixture lead without tracer marks to (hot) black supply lea~ white fixhrra lead or fixture lead with trecer mark

to (neutral) white supply lead. Uninsulated wire is a ground and must be attached to GREEN GROUNO SCREW enclosed in CUPPEO WASHER and tightened
in place to ctossbar, then sunnected to grounding terminal or ground lead inside OUTLET BOX. Use WIRENUTS (local hardware item).
CAUTION Push supply wires and wirenut connections back into OUTLkT BOX.

5. Adjust NIPPLE into CROSSBAR to proper CANOPY depth and secure NIPPLE in place by tightening LOCKNUT against CROSSBAR.
B, Slide CANOPY up CHAIN and secare against ceiling by thraadng KNURLED RING onto CANOPY LOOP.

7. Loosen

8. Raise LOWER FIXTURE ASSEMBLY to MOUNTING

and removethree BATTERY NUTS and STAR WASHERS fromMOUNTING STUDS on LOWER FIXFURE ASSEMBLY.

PLATE on CENTER STEM ASSEMBLY and make
electricalconnections

RING from CANOPY LOOP and allow KNURLEO RING and CANOPY to slide down CHAIN to expose CROSSBAR.

Snap together BLACK

INSTRUCTION SHEET NO.

IS:40714

1292 Page1of 2

●

9,

FIG. 1

1.1<>

9-I TC>LI E la” RRiR511wM:E

WITWCTION SHEET NO.

INSTRUCTIONS FOR INSTALLATION OF

S:40714

!92 Page 2 of 2
JPPORT STEM Attachment AND ADJUSTMEN~

1. Loosen LOWER NUT on end of SUPPORT STEM until it is nearly to the end.

2. Hook opposite end at SUPPORT STEM onto the SUPPORT HOOK on CENTER STEM ASSEMBLY and allow SUPPORT STEM to swing down
so the STEM rest in the SLOT in the SUPPORT BRACKET (Fig. 3A).

3. Tighten LOWER NUT against the SUPPORT BRACKET until SUPPORT STEM draws tight on SUPPORT HOOK (Fig. 3B).

4, Secure in place by tightening UPPER NUT against SUPPORT BRACKET (Fig. 3C).

5. Repeat for remaining SUPPORT STEMS.

IFFUSER CLEANING AND REMOVAL

CAUTION Turn power oft to fixture before attempting to clean.

Diffuser can be cleaned from above the fixture by removing lamps and cleaning DIFFUSER with a soft damp cloth, Should DIFFUSER need to be
removed for cleaning, follow steps below,
1, Remove lamps ~om fixture,’
2, From below fixture, pushup

3. Stide DIFFUSER outon an angle from LOWER FIXTURE ASSEMBLY
NOTE DIFFUSER may have to be gentlycompressedon eitherside to

on one sideofthe DIFFUSER and allow the oppositesideto dropdownpassed HOLDER KNOB (Fig. 1)

TRADITIONAL STYLE RADIANCE PENDANTS CONTINUED

pass fhmugh opening in LOWER FIXTURE ASSEMBLY.

SUPPORTSTEM

UPPERNUT

)WER

NUT

SLOT

SUPPORTaRACKET

SUPPORTARM ~

I “Jk

-,

2

FIG.

/

(

@

LOWER

NUT UPPER

SUPPORTBRACKET

(

NUT

SUPPORT
eRACKET

(