Lightolier IS-40712 User Manual

READAND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

‘hisfislure

o assurefullcompiianc$withlocalcadesandregulations,&e&with yourlocalelectricalinspectorbefore
!stallafion.To preventelectricalshock,turnoff electricityat

FIXTUREASSEMBLYANDINSTALLATION:

is intendedforinstallationinaccordanwwilhtheNationalElectricalCodeendlocalregulations.

fuse box before proceeding,

Retainthese instructions for maintenance reference.

INSTRUCTIONS FOR INSTALLATION OF RADIANCE PENDANT FIXTURES

1. CarefullyremoveCENTERSTEMASSEMBLYfrom

2. Gently pull downward on CANOPY to disengaga from CROSSBAR SPRING CLIPS and axpose CROSSBAR,

3. Mount CROSSBAR and CENTER STEM ASSEMBLY to OUTLET BOX using OUTLET BOX SCREWS (provided with oullet box).

4. Adjust SWIVEL CASTING. For sloped miting appfication$ loosen UPPER LCCK NUT and turn SWIVEL CASTING until “U-SHAPED” opening in

isparallel

NOTE Fixture should only be mounted to mihngs having a maximum slope of 45” or less,

5. Make electrica connections black fixture lead or fixture lead without tracer marks to (hot) black supply lead; white fixture lead or fixture lead with trao?r mark
to (neutral) white supply lead. Uninsulated (bare) fixture wire isagmund and must be connected toa grounding terminal orwirein OUTLET BOX. Use WIRENUTS
(local hardware item). If supply wires are located witfin three inches of ballast, use wire rated for at least 90° C,

6. SldeCANOPY UPCENTERSTEM ASSEMBLY andallowSWIVELCASTING topassthrough square opening inCANOPY. Push CANOPY upunti iffully engages
on CROSSBAR SPRING CLIPS and is sealed flush against ceiting,

7. Loosen and remove three BATTERY NUTS and STAR WASHERS from MOUNTING STUDS on LOWER FIXTURE ASSEMBLY,

8. Raise LOWER FIXTURE ASSEMBLY to

PLATE onCENTER STEM ASSEMBLY and make
electrica connections Snap togetherBLACK
CONNECTOR from LOWER FIXTURE ASSEMBLY tm

to ceiling plane. This procedure can also be used t reorientation of SWIVEL CASTING is desired on non-sloped ceifings.

MOUNTING

packing.

INSTRUCTION SHEET NO.

IS:40712

1292 Page1of 2

\

SWIVEL

9.

9. I <>

9“17-<> 1.1 E m“ WRK’,!ww%ii%i

WTRlfCTfON SHEET NO.

INSTRUCTIONS FOR INSTALLATION OF

S:40712

!92 Page 2 of 2

JSPENSION CABLE Attachment AND ADJUSTMENT

Loosen (do not remove) fhe BATTERY NUTS tha! secure WIREWAY COVERS on each of the three SUPPORT ARMS (Fig. 2 and 3A),

1.

2, Slide each WIREWAY COVER inward towards the renter of the fixiure (Fig, 3A),

3. Position SUSPENSION CABLES through the SLOTS in the end of

4. SifdeeachWIREWAYCOVERoutwardfromthecanterofthe

BA~ERY NUTS (Fig. 3C).

5. Install recommended lamps by snapping base of lamp into SOCKET and allowing tip of lamp 10rest

IFFUSER CLEANING AND REMOVAL

CAUTION Turn power off to fixture before anempting to dean.

CMfusercan be cleaned from above the fixture by removing lamps and cleaning DIFFUSER with a soft damp cloth, Should

removedforcleaning,followstepsbelow,

Removelampsfromfixlure,

1.

2.

Frombefowfixture,pushup on one side of the DIFFUSER and allow the opposite to drop down passed HOLOER KNOB (Fig. 1)

Side OIFFUSER out on an angle from LOWER FIXTURE ASSEMBLY

3.
NOTEOIFFUSERmayhaveFObegentlycompressedoneitherside 10pass through opening in LOWER FIXTURE ASSEMBLY.

RADIANCE PENDANT FIXTURES CONTINUED

WIREWAYCOVERS(Fig,3B},

fixiure untilSUSPENSIONCABLEistau[,Securein position by tightening

on LAMP SUPPORT BRACKET (Fig, 2),

DIFFUSERneedtobe

BATTERYNUT >

SUPPORTARM

WIREWAYCOVER

BA~ERY NUT

.-

))

WIREWAYCOVER -J’

SUPPORTARM

B

/d

FfG.3