Lightolier IS-40616 User Manual

READANDUNDERSTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFIXTUFIE INSTRUCTIONSHEE

IS fwra is intesdedfor installationinacznrdance with tha National Electrical Code and Ictal regulations.

assura full compliance witi local ccdas and regulations, thack with your Id electrical inspactor before

tallation. Toprevent elmtricel shcck, turn off elwtrici~ at fuw box bafora proceeding.

Retaintheseirretrarctimraformaintenancereference.

IS:40616

R0194

Page 10

INSTRUCTIONS FOR INSTALLATION OF A.D.A. TRIO FIXTURES.

COVERSFIXTURES 4tM16WH,4(K16WHE1,40616WHE2,4W16WHN1, 40616WHH1,40616WHN2,

40616sB,4W16SBE1,40616SBE2,40616SBN1,4LW16SBH1,40616sBN2,

40616SC,40616SCEl,40616SCE2,40616SCN1,40B16SCH1AND 40616SCN2

NOTE Thisinstructionsheetcoversbothcompactfluorescentandincandescenttypafirrturea.Althoughilhretrati(

showscompactfhaorescantversion,theincandescentversion assamblesandinstallstha sama.

IACKPIATE INSTALLATION:

1. Loosan two MOUNTING SCREWS in LOWER MOUNTING BRACKFE and ramove OIFFUSER ASSEMBLY by pulling OIFFUSER ASSE
from LOWER MOUNTING BRACKETS and unhooking ASSEMBLY from two UPPER MOUNTING BRACKETS (Fig. 1, Fig. 2 and Fig. 3).

2. Thraad CROSSBAR MOUNTING SCREWS into CROSSBAR as shown in Fig. 1.

3. Using appropriate slots in CROSSBAR, sacure CROSSBAR to OUTLET BOX using OUTLETBOX SCREWS (providad with OUTLET 60)

4. While supporting BACKPLATEmaka connations black fisture laad or fixtura Iaed without trmar marks to hot (black) supply Iaad; v

lead or fisture lead with tracar marks to nautral (white) supply Iced. Uninsulated fklura wire is a ground wire and must be connect,
grounding tarminal or connections back into OUTLET BOX.

5. Position BACKPU+TE over CROSSBAR allowing CROSSBAR MOUNTING SCREWS to coma through holas in BACKPLATE.

CAUTION:Make certain wires ara not pinched between parts.

6. SacureBACKPL4TEbyinstallingtwo BA~ERYNUTSoverCROSSBARMOUNTINGSCREWSandtighten.

7. Installracommendadlamp(s).

CAUTION MAXIMUM WAITAGE AS MAFIKEDONFIXTUREMUST NOTBEEXCEEOEO.

o

CR
Sc

1-1

C3HTC>LIEl?’:::+’:~f~

NSTRUCTIONStlE~ NO.

1S:40616

lM6t

)IFFUSERINSTAU.ATION

1. HookDIFFUSIR ASSEMG4Yover UPPER.MOUNTINGBRACKETSallowing UPPERMOUNTING SCREWSto go down into holes in UPPERMOUNTING

2. SecureOIFFUSERASSEMBLYin positionbytighteningtwo LOWERMOUNTING SCREWSintoLOWERMOUNTING BRACKETS(Fig.3).

Page2012

WIACKETS,swing OIFFUSERASSEMBLYagainst EACKFLATE(Fig.2).

wvMOuNT’NG

/-

INSTRUCTIONS FOR INSTALLATION OF A.D.A. TRIO FIXTURES.

COVERSFIXTURES 40616WH,4M16WHE1, 4&16WHE2, 4tNi16WHNl, 4W16WHHI,

AW16WHN2,4061.6SB,40616SBE1,.40616SBE2,4LM16SBN1,40616SBH1,41W16SBN2,

4iW16SC,~6SGEl, 60616SCEZ4W16SCN1,4Mi16SCHl ANO 4M16SCM

)

~ UFPERMOUNTING

J

iihACKET

DIFFUSERASSEMBLY

B

LOWERMOUNTING
SCREW

R

- LOWERMOUNTING

\

= GACKFIATE

BRAcKH

M.2

FIG.3