Lightolier IS-26060 User Manual
READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY
INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC®TRACK ITEM.
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal
code specifications. To assure full compliance with codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
®
INSTRUCTION SHEET NO.
IS:26060
0597 Page 1of 2
END FEED AND FLOATING CANOPY MOUNTING KIT - FLUSH AND STANDOFF VERSIONS
FOR USE WITH PROSPEC
®
SURFACE MOUNT TRACK SYSTEMS ONLY
END FEED MOUNTING INSTRUCTIONS
(Flush 26060WH, BK and Standoff 26061WH, BK)
Mounting the CANOPY at the end of FEED TRACK or directly above
a FEED CONNECTOR.
1. Mark CENTER LINE for TRACK through CENTER LINE of OUTLET BOX.
2. NOTE: The CANOPY mounts to a 3 or 4” OCTAGON OUTLET
BOX. The MOUNTING HOLES of the OUTLET BOX should be at
45° to the longitudinal axis of the TRACK. (Fig. 1)
3. Remove the KNOCK OUT PLATE from the FEED TRACKor
CONNECTOR (retain the SCREW). (Fig. 2)
4. Prepare TAB on the PLATE ASSEMBLY as follows:
• FEED TRACK: DO NOT BREAK ANY TAB. (Fig. 2)
• POWER EXTENSION, IN-LINE, “T”, AND “ X” CONNECTORS:
BREAK THE 90° TAB OFF THE PLATE ASSEMBLY. (Fig. 3)
• “L” CONNECTOR: BREAK THE 90° TAB AND THE STRAIGHT
TAB FROM THE PLATE ASSEMBLY. (Fig. 4)
5. Attach the PLATE ASSEMBLYonto the FEED TRACK or
CONNECTOR using the SCREW. (Fig. 2 & 3)
6. Mount the TRACK to the ceiling (see instruction sheet
IS:26000 provided with the TRACK) passing the wires through
the center of the PLATE ASSEMBLY.
7. Rotate the PLATE ASSEMBLYuntil the SLOTS are in-line with
the MOUNTING HOLES on the J-BOX.
8. Secure the PLATE ASSEMBLYto the J-BOX using the THIN
HEAD SCREWS. (Fig. 5)
9. Attach the GROUND WIRE on the CANOPY PLATE to the
GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 5)
10. WHEN USING THE FLUSH CANOPY 26060WH/BK.
Slide the CANOPY PLATE between the CONNECTOR and
CROSS BAR on the PLATE ASSEMBLY. For added security of
CANOPY PLATE: Drill a hole in CANOPY PLATEand secure to
ceiling with a screw.
11. WHEN USING THE STANDOFF CANOPY 26061WH/BK
Slide the CANOPY PLATE between the CROSS BARand NUT
on the PLATE ASSEMBLY. Rotate the NUTto secure the
CANOPY PLATE against the ceiling. (Fig. 8)
NOTE: THE CROSS BAR MUST COVER THE SLOT IN
THE CANOPY PLATE AFTER ASSEMBLY.
12. Follow the instructions for wiring on the instruction sheet
included with the “FEED TRACK” or “CONNECTOR”.
CAUTION: TURN OFF POWER AT FUSE BOX BEFORE
INSTALLING THE CANOPY KIT
POWER EXTENSION
CONNECTOR
PLAT E
ASSEMBLY
SCREW
90 ° TA B
KNOCK OUT
PLATE
FIG. 2
FIG. 3
PLAT E
ASSEMBLY
SCREW
KNOCK OUT
PLATE
FEED TRACK
FIG. 4
STRAIGHT
TAB
PLATE
ASSEMBLY
90 ° TA B
KNOCK OUT
PLATE
“L” CONNECTOR
CANOPY
PLATE
GROUND
WIRE
THIN HEAD
SCREW
J-BOX
FIG. 5
CROSS BAR
CROSS BAR
45 °
TRACK UNIT
LONGITUDINAL
TRACK
OUTLET BOX
OUTLET BOX
MOUNTING HOLE
FIG. 1
READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY
INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC®TRACK ITEM.
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal
code specifications. To assure full compliance with codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
®
INSTRUCTION SHEET NO.
IS:26060
0597 Page 2of 2
FLOATING FEED MOUNTING INSTRUCTIONS
(Flush 26060WH, BK and Standoff 26061WH, BK)
Mounting the CANOPY at some distance away from the end of the
FEED TRACK or FEED CONNECTOR.
NOTE: Hardware is supplied to mount the CANOPY a maximum
of 4 feet from the FEED CONNECTOR. DO NOT EXCEED
THIS DISTANCE.
1. Mark CENTER LINE of TRACK through CENTER LINE of OUTLET BOX.
2. NOTE: The CANOPY mounts to a 3 or 4” OCTAGON OUTLET
BOX. The MOUNTING HOLES of the OUTLET BOX should be at
45° to the longitudinal axis of the TRACK. (Fig. 1)
3. Break the BARRIER off the FEED CONNECTOR or FEED TRACK.
(Fig. 6)
4. Remove the DEAD END from the TRACK and retain.
5. Assembly the “U” BRACKET onto the PLATE ASSEMBLY using
the FLAT HEAD SCREW. (Fig. 6)
6. Run the feed wires along the top of the TRACK and into the
FEED CONNECTOR or FEED TRACK. (2 HOTS, 2 NEUTRALS,
AND GROUND; MAXIMUM)
7. NOTE: USE 12 GA. COPPER THHN WIRE INCLUDING
GROUND. IF STRANDED 12 GA WIRE IS USED THE ENDS
MUST BE TINNED.
8. Cut the WIRE COVER to the desired length.
9. Slide the WIRE COVER (over the wires) and PLATE ASSEMBLY
into the TRACK. NOTE THE POSITION OF THE 90° TAB IN
RELATION TO THE FEED-IN POINT. Pass the wires
through the center hole of the PLATE ASSEMBLY.
10. Secure the PLATE ASSEMBLY to the TRACK by tightening the
SCREW. THE WIRE COVER MUST COVER THE ENTIRE
LENGTH OF WIRES ON TOPS OF THE TRACK.
11. Mount the TRACK to the ceiling (see instruction sheet 26000
provided with the track or IS:26478). Positioning the PLATE
ASSEMBLYover the J-BOX.
12. Splice the wires from the track to the wires in the J-BOX.
BLACK TO BLACK, WHITE TO WHITE, AND GROUND TO
GROUND.
13. Rotate the PLATE ASSEMBLY until the SLOTSare in-line with
the MOUNTING HOLES on the J-BOX.
14. Secure the PLATE ASSEMBLY to the J-BOX using the THIN
HEAD SCREWS. (Fig. 7)
15. Attach the GROUND WIRE on the CANOPY PLATE to the
GROUND LEAD or GROUND TERMINAL in the J-BOX. (Fig. 7)
16. WHEN USING THE FLUSH CANOPY 26060WH/BK.
Slide the CANOPY PLATE between the TRACK and CROSS
BAR on the PLATE ASSEMBLY. For added security of CANOPY
PLATE: Drill a hole in CANOPY PLATEand secure to ceiling
with a screw.
17. WHEN USING THE STANDOFF CANOPY 26061WH/BK.
Slide the CANOPY PLATE between the CROSS BAR and NUT
on the PLATE ASSEMBLY. Rotate the NUTto secure the
CANOPY PLATE against the ceiling. (Fig. 8)
18. NOTE: THE CROSSBAR MUST COVER THE SLOT IN
THE CANOPY PLATE AFTER ASSEMBLY.
19. Follow the instructions for wiring on the instruction sheets
included with the the “FEED TRACK” or “CONNECTOR”.
20. Assembly the DEAD END into the end of the TRACK.
FIG. 6
BARRIER
DEAD
END
U BRACKET
90 ° TA B
FLAT HEAD
SCREW
PLATE
ASSEMBLY
WIRE COVER
TRACK UNIT
FEED CONNECTOR
FEED IN POINT
U BRACKET
FIG. 8
TRACK UNIT
J BOX
CANOPY
PLATE
POWER EXTENSION
CONNECTOR
NUT
FIG. 7
CANOPY PLAT E
J-BOX
PLATE
ASSEMBLY
WIRE COVER
POWER EXTENSION
CONNECTOR
TRACK UNIT
THIN HEAD
SCREW
CROSS BAR
Loading...