Lightolier IS-2000LVNT User Manual

INSTRUCTION SHEET NO

INSTRUCTIONS PROCEDURE FOR LOW VOLTAGE
FRAME=fN KIT WITH REM~E TRANSFORMER

IS:2000LVNT

0191

Page 1 of 2

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code or local regulations. To
asaure full compliance with local codes and regulations,

installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference

check with your local electrical inspector before

N~E FRAME-fN KIT IS PROVIDED WITHOUT TRANSFORMER. TRANSFORMER MUST BE PROVIDED SY

OTNERB. LIGHlOLIER CAT #B60S AND 8609 TRANSFORMERS MAy BE USED.

CAUTION: THIS FRAME-IN KIT IS RATED AT 42VA. USE ONLY 12V. AC. INPUT.

FIG. A

1. FRAME-IN

FIG. B FIG. C

2. CLOSE-IN

3. SNAPON

FIG. D

4. PUSH-UP

WARNING—(RISK OF FIRE) DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FiXTURE SIDES OR

WIRING COMPARTMENT, NOR ABOVE FIKTURE IN SUCH A MANNER TO ENTRAP HEAT.

1.

FRAME.IN (Fig. A)
Faaten MOUNTING FRAME to wood joist. Line

2.

N~E For wat plaster ceiling, uae Plaster
Ring Accessory No. 1959 (order aaparately).

SNAPIN (Fig. C).

3.
PUSH-UP (Fig. D).

4.

SEE BACK PAGE FOR LAMPING INSTRUCTIONS.

SEE SEPARATE
REFLECTOR TRIM
INSTRUCTION

I

SHEETS.

LK59-ITC>949

L

4&=---- ‘OTO”cL’p

FIG G

[=@sEcAucus> NEw JERSEY,07096

* MO NT REAL, QUEBEC, C AN ADA

LAMPING
NOTE Socket manufacturers have suggested that

socket may fail after 3 to 6 relampings. If this
occurs socket can be replaced by disconnecting
male connectors (attached to socket leads) from

female connectors (attached to fixture leads) and
replacing it with a naw socket procured thtiugh

Lightolier (Fig H.).

1. Make sure that power is OFF when Iamping
or relamping. Remove LAMP RING from

SOCKET CUP by pulling etraight down.

2. Ineeft LAMP @fR-16) between LAMP

SPR NGS until face of lamp sits firmly on
GLASS LAMP GUARD (Fig. l).

INSULATINGSLEEVING

+Q

~ FEMALE CONNECTORS

(Attached to

--

Fixture V4res)

~&OOOLVNT
Page 2 of 2

MALECONNECTORS

(Altaohedto socketWires)

MR16 SOCKET

L

3, Attach SOCKET to hi-pin prongs on LAMP

4. Insert LAMP RING with LAMP and GLASS

LAMP GUARD back into SOCKET CUF!

AIMING ANGLE ADJU=MENT (Fig. J)

1. For vertical adjustment, insert blade of
screwdriver into the open slot of YOKE.

2. Using the screwdriver as a lever, tilt the entire

LAMP HOLDER to the desired angle.

3. ~~L~#mtal adjustment, rotate tie LAMP

LAMP

-#

GLASS LAMP
GUARD

&

FIG. H

cf5-’-s0cKET

- LAMP SPRING

LAMP RING

t

FIG. I

OCKET CUP

LAMP HOLDER

NOTE 1. LOW VOLTAGE FIXTURES should be APERTURE TRIM

dimmed only wNh speciel dimmers intended
specifically for that purpose. Use Llghtoller
Lytemode Scenlst,

Crescendo VA, Neptune VA,

Yo

Preclslon VA, Esayset VA,Sunriee VA, Redlsnt VA or
equivalent products by others ,or verieblo

sutotranaformera or

electronicdlmmeraintendedfor

usewithlowvoltageflstuma.2. QW voltsgefixtures

ASSEMSLY

~,

~.

~.,

~.y::,?
mey produoe eudible sound when ueed with
dimme~

critical sreaa.

which may be objectional in acoustically

FIG. J

NOTE Followthe mex. wire length recommended

below to minimize voltsge drop. Voltage drop will
affect the brlghtneaa and color of the light.

~