Lightolier IS-1161-A User Manual

INSTRUCTION SHEET NO.

THIS REFLECTOR TRIM MUST BE INSTALLED

IN LIGHTOLIER’S

:EAD AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

~is fixture is intended for installation in accordance with the National Electrical Code and local regulations. 3 assure full compliance with local codes and regulation, check with your local electrical inspector before

lstallation.

stain thasa Inatructlona for maintananca reference.

IOTE Uaa this Instruction Sheet only when Lytecaatar Reflectcr Trim ie being instelled in the 1100 series

kama-hr-f(its with ROTO.CLIPS (ace Fig. E). If not, disregard this Instruction Sheet. N is reccmmanded YCU naintein e copy of the following instructions for reference.

To prevent electrical shock, turn off electricity at fuse box before proceeding.

%gE=

1100 SERIES FRAME-IN.KIT ONLY

IS:1161A

06w

Page 1 of 2

FIG. A

1. FRAME-IN 2. ROTATE CLIPS

WARNING: BEFORE INSTALLING REFLECTOR TRIM TO FRAME4N KIT, READ MARKINGS IN REFLECTOR TRIM AND IN SOCK= CUP OF FRAME4N.KIT TO D~RMiNE LAMP WAlTAGE AND TYPE APPLICABLE FOR YOUR

iNSTALLATION. IF LC. TYPE FRAMING KfT IS USED, iT MAY BE INSTALLED IN DIRECT CONTACT WITN lNSUfATED CEIUNGS. IF A NON LC. lYPE FRAME4N4(iT IS USED, 00 NOT INBTAU lNSULATfON WiTHiN 31NCHSS OF FfXIWRE SIDE OR WIRING COMPARTMENT, NOR ABOVE FfXTURE IN SUCH A MANNER TO ENTRAP HEAT.

1. FRAME.IN (Fig. A)

See Freme-in-Kit instruction Sheets, for

installation procedure.

2. ROTATE ROTO-CLIPS (Fig. B) Rotate (4) ROTO CLIPS so that the shofi legs

extend inwardly toward the center opening (Fig. F).

NOTE The SHORT LEG cf the ROTO CLIP haa NO return on top. (Fig. E & F).

‘RIM INSTALLATION

3. Insert HOOK in ear of SPRING on SOCKET CUP and let HOUSING hang down (Fig. H). Straw SOCKET EXTENSION (MALE ADAPTER) into SOCKET in SOCKET CUP.

FIG. B

g:’’LqLO”GLEG

FIG. C

3. SNAP.ON

‘-” FIG. E

FIG. D

4. PUSH.UP

. ..-..,.:.

FIG. F ‘-’:::~..,

HOUSING

4. Disengage HOUSING from SOCKET CUP pulling HOOK out of SPRING ear (Fig. G). Insert SOCKET CUP between tabs on MOUNTING

BRACKET, making sure SPRINGS snaps into

slote of MOUNTING BRACKET (Fig. C).

5. Tilt HOUSING and insert SOCKET CUP into ceiling openin on side opposite junction box,

flange on HOUSING is flush to ceiling (Fig. D).

SEE BACK FOR LAMP INSTALLATION AND ADJUSTMENT

U.S. PATENT NO, 4,&ZW244,3f3,154 end 4,32T#Gl FOREIGN PATENT3 PENDING.

K5+1TC>IJE R“:v:::::i,N::

8pivot HOUSIN and push it up into ceiling until

by FIG. G

FIG. H

LAMPING INSTRUCTIONS AND ADJUSTMENT/LOCKING

INSTALL LAMP

NOTE Socket

manufactures hsve suggested

thst socket may fail after 3 to 6 relsmphrgs.

If this occurs socket csn be repleoed by disconnecting msle connectors (attached tc socket leads) from female connecters

(attached to fixture Ieads) and replacing it with a socket prccured through Llghtoller,

see Fig. 1.

6. Remove LAMP RING from LAMP/ YOKE HOLDER by pulling straight down (Fig. J).

7. Insert LAMP [MR-16) between LAMP SPRINGS until face of iamp shs firmly on GLASS LAMP

GUARD (FicI. K).

8. Attach SO~KET to hi-pin” prongs on LAMP

(Fig. K).

9. Insert LAMP RING with LAMP and GLASS LAMP GUARD attached back into LAMP / YOKE HOLDER (Fig. L),

INSULATING SLEEVING

LAMP/ YOKE

FEMALE CONNECTORS

(Attached to Fixture Wires)

FIG. I

HOLDER ~

/’”_ (At::~:d::!::k~O::as)

MR16 SOCKET

IS1161.A

0690

2 of 2

Page

VERTICAL / ANGLE ADJUSTMENT AND LOCK

(Fig. L)

10. Ineert a screwdriver into the LOCKING GUIDE on the LAMP YOKE HOLDER and locate the slot in the VERTICAL ADJUST/ LOCK SCREW.

Turn the SCREW counterclockwise, and using

the screwdriver as a lever, tilt the entire

LAMP / YOKE HOLDER to the desired angle, Once the desired angle is reached, tighten screw by turning screwdriver clockwise.

HORIZONTAL ADJUST AND LOCK

11. The entire ~MP I YOKE HOLDER can be horizontally rotated to aim the angle of light as

leaves the hole in the APERTURE TRIM. This

can be done by backing off the HORIZONTAL ADJUST / LOCK SCREW (not shown) one full turn, freeing the SUPPORT PLATE (Fig. L). Grasping the YOKES on either side of the

LAMP / YOKE HOLDER, ROTATE THE SUPPORT PLATE to the desired angle and lock the position by tightening the HORIZONTAL

ADJUST / LOCK SCREW.

RELAMPING: The locking mechanisms designed

within this fixture allow relamping without

having to readjust and relock. Following Steps

6-9.

WARNING: 1. LAMP MANUFACTURES REQUIRE THE GLASS

LAMP GUAR,DBE IN PLACE BEFORE Energizing LAMP,

AND THAT

FULLY COOLED BEFORE RELAMPING. AVOID FINGER MARKS

ON INSIDE OF LAMP POR ,THEY MAY CAUSE SHORT LAMP

LIFE AND POSSIBLE BREAKAGE.

2. USE

INC.

VOIDS THE UNDERWRITERS LABORATORIES LISTING AND

COULD CONBTtTUTE A FIRE HAZARD.

GREAT CARE MUST BE TAKEN THAT LAMP IS

ONLY REFLECTOR TRIMS PROVIDED SY LIGHTOLIER

USE OF OTHER MANUFACTURER’S REFLECTOR TRIMS

FIG. J

‘:+

SPRING

GUGfi~RyMP

NOTE 1. LOW VOLTAGE FIXTURES should be dimmed only

with special dimmers intended for that purpose. Use Llghtolier Lytemode, Sceniat, Cre!$cendc VA, Netpune VA, Precision VA, Eesyset VA, Sunrise VA, Red lent VA or equivalent products by others or variabla autc-transformers or electronic dimmers Intendad for uee with low voltsga fixtures. 2. Low voltsge flxturaa mey produce eudlble sound whan used with dimmara which msv be oblamtionei in acoustically crltlcal areas.

. . . . . .

Lightolier IS-1161-A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual