Lightolier IS-1155 User Manual

/

INSTRUCTION SHEET NO.

lN=ALLATION OF LYTECA~ER REFLEOTOR TRIM

IN THE 1100 SERIES FRAME-IN-KIT WITH ROTO CLIPS

IS:1155

R0487

_

READ AND UNDER~AND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation

code specifications. To prevent electrical shock, turn off electricity at fuee box before proceeding.

in accordance with the National Electrical Cods and local or federal

NOTE Use this Instruction Sheet only when Lytecsster Trim is being Installed in the 1100 series Frsme-im

Kits with Roto Cfips (see Fig. F). If not, disregsrd this Instruction Sheet.

a

%%

\

FIG. A

1. FRAME-fN

FIG. B

2. ROTATE CLIPS

FIG. C

3. SCREW4N

FIG. D

4. SNAWN

FIG. E

PUSH.UP

WARNING: BEFOREinstalling REFLECTORTRiM lU FRAME-fN Km,READ MARKINGS IN REFLECTORTRIM
AND IN SOCK= CUP OF FRAME.fN-KIT TO D~ERMINE LAMP WAT7AGE

lNSTALLATfON. IF IC. TYPE FRAMING KIT IS USED, IT MAY BE iNSTAUED IN DiRECT CONTACT WITH INSULATED

CEILING. IF A NON il$. TYPE ~ME-fN-KfT IS USEQ DO N~ iNWAU INSULATION WITHIN 3

SIDE OR WIRING COMPARTMENT,

NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HSAT.

1. FRAME-fN (Fig. A)

See Frame-In-Kit Instruction Sheets for installation

procedure.

2. ROTATE ROTO.CLIPS (Fig. B)

Rotate (4) ROTO CLIPS eo that the short legs extend
inwardly toward the center opening (Fig, F)

NOTE The SHORT LEG of the RCf70 CLiP hss NO

return on top.

3. SCREW-IN MALE ADA~ER (Fig. C)

Insert HOOK

let HOUSING hang down (Fig. G). Screw SOCKET
EXTENSION (MALE ADAPTER) into SOCKET in
SOCKET CUi?

4. SNARON SOCK~ CUP (Fig. D)
Disengage HOUSING from SOCKET CUP by pulling

HOOK out of SPRING ear (Fig. H). Insert SOCKET
CUP between slots on MOUNTING BRACKET
making sure SPRINGS snap into slots of MOUNTING

BRACK= (Fig. l).

in ear of SPRING on SOCKET CUP and

SHORT LEG

/

>

.-..,.:. ....

:3;

q

50CKETcup

AND TYPE APPLICABLE FOR YOUR

INCHESOF FfXTURE

LONG LEG

/

@

0=

-..,,

......

SPRING

HOOK

HOUSING

HOUSING

FIG. H

N

5. PUSH-UP HOUSING (Fig. E)
Tilt HOUSING and inserf SOCKET CUP into ceiling

opening on opposite side of JUNCTION BOX. Pivot
houeing and push it up into ceiling.

SPRING

SOCKETCUP

MOUNTING

PATENTNO 4,313,154;4,327,403.

US,

FOREIGN PATENTsPENDING

[mg<~[=[~<>[m[l~g? MONTREAL, Q”EBEC, CANADA

FOR OTHER REFLECTOR TRIMS Eyebell (1162), etc See bsck pS9e

BRACKET

@ SEC AU CUS, NEW JERSEy,07094.0508

IN!YCALLATION OF ADJUSTABLE ACCENT LIGHT (LOW VOLTAGE TRIM)

6. Remove lAMPHOLDER RING from within HOUSING
by pulling straight down, and disengaging ths LAMP
SPRINGS which also act se a holding mechanism for
lAMPHOLDER RING.

1s1155

R0487

swHG-

7. Select voltage (12v., 25-50 Watt, or 5.5v, 25 Watt)
depending on lamp being used? by setting SLIDE
SWITCH (Fig. J). Insert screwdriver into slot and slide
switch if not already set according to lamp being
used (See Fig. K).

8. Install proper wattage PAR36 LAMP into IAMP
CONNECTOR, making certain the LAMP is seated all
the way into the IAMP CONNECTOR.

9. Insert LAMP into LAMPHOLDER RINGS so that face
of LAMP is seated, and extended through hole in the
LAMPHOLDER RING, and put the lamp and ring
back into the LAMPHOLDER SUPPORT so that the
LAMP SPRINGS now support all.

m4srALumor4 OF

6. Remove APERTURE TRIM from within EYEBALL by
pullin straight down, and disengaging from
SUPP?)RT SPRINGS (Fig. L).

7. Select voltage (12v.,25-50 Watt, or 5.5v, 25 Watt)
depending on lamp being used! by eetting SLIDE

SWITCH (Fig. L). Insert screwdrwer into slot and slide
switch if not alreedy set according to lamp being
used (See Fig. K).

EVEBALL (mw VOLTAGE TRIM)

LAMP HOLDER -

SUPPORT

LAMP >

CONNECTOR

HOUSING

LAMP=------

LAMP HOLDER ~

RING

SLID

w

ti~.

\H “\-

\.

Q

\

A

. ...

...’

/“

FIG. J

FIG. K

6. Install proper wattage PAR36 LAMP into LAMP
CONNECTOR, meidng certain the LAMP ia seated all
the way into the IAMP CONNECTOR (Fig, L).

9. Insert LAMP into LAMP SPRING.

10, Insert APERTURE TRIM, and LAMP into EYESALL

until groovee on APERTURE TRIM engage into

SUPPORT SPRINGS [FiO. L).

NOTE LOW VOLTAGE &i+lJRE6 should be

dimmed only with speclel dimmers Mended for
that purpose. Use Ughtoller Preolslon LV, Eoeniet,
or Lytemcds, or equlvelerrt products
vsrieble eutc-transformers or eleotrcn c dimmers

intended for uee with low voltege flsturss.
NOTE law voltege flstures may produce sudible

sound when used with externel dimme~ which mey
be objectlonsl In acoustically critlcsl srea%

WARNING USE ONLY REFLECIOR TRIMS PROVIDED SV LIGHTDLIER INC. USE OF ~HER MANUFACTURERS
REFLECIUR TRIMS VOIDS THE UNDERWRITERS IABOFIA30RIES L16TING AND COULD CONSIWIJTE A FIRE
HAZARD.

~others or

co

FIG. L