Lightolier IS-1152-A User Manual
---
/
..-_.. __.. ..—–— —
INSTRUCTION SHEET NO,
THIS REFLECTOR TRIM MUST BE INSTALLED
IN LIGHTOLIER’S I102P1 FRAMEdN.KIT WITH ROTO CLIPS ~W ■
7,
lS:1152-A
Page1 of 2
READ AND UNDERSTAND THESE lN~RUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
accordance with the National Electrical Code and local regulations.
Retain these Instructions for mslntensnce refererrc-
%%E=
‘P
FIG. A FIG. B
1. FRAME-fN
WARNING—(FilSK
I
1. FRAME-fN (Fig. A)
See Frame-In-Kit Instruction Sheets IS-I 102, for
installation procedure.
2. ROTATE ROTO-CLIPS @g. B)
Rotate (4) ROTO CLIPS so that the short legs extend
inwardly toward the center opening (Fig. F)
NOTE The SHORT LEG of the ROTO CLIP hes NO
return on top. (Fig. E & F).
TRIM lNSTALLATfON
3, Remove PINHOLE FACE PLATE from HOUSING by
inserting fingeta in aperture and pull apart fmm
HOUSING (Fig. G).
4. Insert HOOK
let HOUSING hang down (Fig. H). Screw SOCKET
EXTENSION (MALE ADAPTER) into SOCK~ in
SOCKET CUR
5, oisengage HOUSING ftom
HOOK out of SPRING ear (Fig, G). Insert SOCKET CUP
between tabs on MOUNTING BRACKm making sure
SPRINGS snaps into slots of MOUNTING BRACKR
(Fig. c).
WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HSAT.
in ear of SPRING on SOCKfl CUP and
OF FIRE) DO NOT INSTALL lNSUIATfON WITHIN 3 INCHES OF FIXTURE SIDSS OR
2. ROTATE CLIPS 3. SNAPGN
SOCKET CUP by pulling
.
-,,;, “...! .,,.’’:, ...
q,
Zw%%%
‘@
-<,,
w
. . . . .
GREENFIELD
~u~Er
MALEADAPTER
FIG. C
SHORT
sHORT LEG
‘-/ \\_
ROTO-CLIP
(4 AROUND
-.
‘“’ “G” A:?
Y
q?
b404c~&G
4. PUSH-UP
LEG
\
*,, =
,.,(.:;:.J..-,
-+
— SPRING
G=
I
./
FIG, D
[
m
0=/
#’--
~ FIYEH8?F,
FIG. G
LONG
HOUSING
I
LEG
‘m
,, ,’
6, Tilt HOUSING md insert SOCKH CUP into ceiling
opening on side opposite junction box, pivot HOUSING
and push it up into ceiling until flange on HOUSING is
flush to ceiling (Fig, D).
U.S. PATENT NO. 4,&?S,%22,4,313,154and 4,32T,403
FOREIGNPATENTS PENDING,
SEE BACK FOR f.AMP lNSTALIATfON AND ADJUSTMENT
B-1 C51”ITC>I-1 IE la” iv;:;::i,N::;:::,E:iiT;:
HOU
s
INSTALLATION OF LYTECASTER REFLECTOR TRIM
IN THE 1102 FRAME-IN-KIT WITH ROTO CLIPS
151152.A
0690
Page2
of 2
TRIM lNSTALLATtON(Contd)
INSTALL LAMP
NmE Sooket manufactures have suggested
that socket may fall after 3 to 6 ralampinge. If
thla occurs sooket cart be replaced by
dlaconnectlng male connectom (anached to
socket Ieada) from female connectors
(attached to flstura leads) and replacing it
with a socket procured through Lightoller,
see Fig. L
7. Remove LAMP RING from IAMPNOKE HOLDER by
pulling straight down (Fig. J),
8. Insert LAMP (MR-16 Bulb) between LAMP SPRINGS
until face of bulb sits firmly on GLASS LAMP
GUARD (Fig. K).
9. Attach SOCKET to hi-pin prungs on LAMP (Fig. K),
(NUIT% No polarity of pins required).
10. Insert LAMP RING
GUARD attached back into IAMPNOKE HOLDER.
VERTICAUANGLE ADJUSTMENT AND LOCK
11. Insert a screwdriver into the LOCKING GUIDE on the
LAMPNOKE HOLDER, and locate the slot in the
VERTICAL ADJUST/lQCK SCREW. turn the SCREW.
counterclockwise+ and using the screwdriver as a ‘
lever, tilt the entire LAMP/’fOKE HOLDER to the
desired angle. Once the desired angle is reached,
tighten ecraw by turning screwdriver clockwise until
snug tight.
with LAMP and GLASS LAMP
INSULATING SLEEVING >
(Attached to Fixture WE.)
““’’’K’v%
G
“..
FEMALE CONNECTORS
/ {At~aci;di;”50CGt-tik.,
FIG. I
~– -’
- MA! F C.ONNHTCIRS
MR16 SOCKET
FIG. J
HORIZONTAL ADJUST AND LOCK
12. The entire lAMP/YOKE HOLDER can be horizontally
rotated to aim the angle of light through the hole in
the FACE PLATE TRIM (Fig. K). This can be done by
racking off the HORIZONTAL ADJUST/~CK SCREW
one full turn freein the SUPPORT PIATE (Fig. K).
Grasping the YOKE on either side of the LAMPNOKE
HOLDER. rotate the SUPPORT PLATE to tha desired
angle, and lock the poeition by tightening” the
HORIZONTAL ADJUSWU3CK SCREW. Replete INSERTS
13, Insert PINHOLE FACEPLATE,
RELAMPING The locking mechanism in this fixture allow relamping without having to readjust and
rslock. Follow Steps 7-10 and 13,
8
NOTE 1. LOW VOLTAGEFIXTURES should be dimmed only with speciai dimmers intended
specifically for that purpose Use Lightolier Lytemodq Soeniat, Crsacendo VA, Neptune VA,
Precision VA, Easyaet VA, Sunrise VA, Radiant VA or equlvalant products by others or variabie
auto-transformera or eiactronic dimmers intendad for use with iow voltage fixtures. 2. Low
voitage fisturas may produce audibie sound whan usad with dlmmere which may be objectionai
in acouaticaiiy criticai areas.
WARNING: 1. LAMP MANUFACWRES REQUiRE THE GLASS LAMP GUARD BE IN PLACE BEFORE
Energizing LAMR AND
BEFORE RELAMP!NG. AVOID FiNGER MARKS ON INSIDE OF LAMP FOR THEY MAY CAUSE SHORT
LAMP LIFE AND POSSIBLE BREAKAGE.
2. USE 0NL% REFLECIX)R “TRIMS PROViDED BY LiGHTOLIER INC. USE OF Uf’HER
MANUFA~URER’S REFLECTOR TRiMS VOIDS THE UNDERWRITERS LABORA~RIES LiSTING AND
‘ COULD Constitute A FIRE HAZARD.
THAT GREAT CARE MUSr BE TAKEN THAT LAMP IS FULLY COOLED
J
Loading...