Lightolier IS-1062LV User Manual
w
i%%wyi!liwn
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALUNG FtXTURE
This fixture is intendedfor installationin accordancewith the NationalElectricalCode and local
regulations.Toassurefullcompliancewithlocalcafes andregulations,checkwithyourlocalelectrical
inspectorbeforeinstallation.Topreventelectricalshock,turnoffelectricityatfuseboxbeforeproceeding.
Retain these instructions for maintenance reference.
INSTRUCTIONS FOR INSTALLATION OF REFLECTOR TRIM 1062LV
IN THE 10OOLV FRAME- IN-KIT
?? s
INSTRUCTION SHEET NO.
Y
IS:1062LV
0192 Page 1 of 2
Fig. A Fig. B Fig. C
1. FRAME-IN
2. CLOSE-IN
WARNING: BEFORE INSTALLING REFLECTOR TRIM FRAME4N
KIT, READ MARKINGS IN REFLECTOR TRIM AND ON SOCKET CUP
OF FRAME-IN KIT TO DETERMINE LAMP WAllAGE AND TYPE
APPLICABLE FOR YOUR INSTALLATION. IF I.C. TYPE FRAME-IN KIT
IS USED, IT MAYBE INSTALLED IN DIRECT CONTACT WITH
INSULATED CEILING. IFA NON LC.TYPE FRAME-IN KIT IS USED, DO
NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR
WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER
TO ENTRAP HEAT.
1.FRAME-IN (Fig. A)
See Frame-InInstructionSheetfor installationprocedure.
2, ROTATE ROTO-CLIPS(Fig. B)
As shown in Fig. E.
3, SNAP-ON (Fig. C)
lnsertSOCKETthrough RECTANGLEHOLEontopof REFLECTORTRIM.
EngageTABfrom SOCKETCUP into one of the SLOTSontopof
REFLECTORTRIM and push otherendof SOCKETCUPwith LANCING
intothe other (Fig. F).
4. PUSH-UP(Fig. D)
PushREFLECTORTRIMintoceilinguntilflange isflushto ceiling(Fig.D).
NOTE: Socket manufacturers have suggested that socket may fail after
3 to 6 relampings. If this occurs, socket can be replaced by disconnect
ing male connectors (attached to socket leads) and female connectors
(attached to fixture leads) and replacing it with a new socket procured
through LIGHTOLIER (Fig, G).
INSULATINGSLEEVING MALECONNECTORS(AllACHED TO SOCKETWIRE)
FEMALECONNECTORS(ATTACHEDTO FIXTUREWIRES)
3. SNAP-ON
ROTO-CUP
POSITION
RECTANGLEHOLE
SLOTS
Fig. D
4. PUSH-UP
FRAM-INKIT MOUNTS
FLUSHON CEIUNG
.,. ... :.,- .. ..
Fig. E
TRIM
\l (
SOCKET
Fig. F
- ~@MR’’”KH
SEE BACK PAGE FOR IAMPING INSTRUCTIONS
1. I es
l“ITC>1.1E R“
Fig. G
INSTRUCTION SHEET NO.
IS: I062LV
0192 Page 2 of 2
LAMPING
1.Checkto sea that power is OFF beforeIampingor relamping.
2. Removebaffleaperturefrom ELBOWby pullingstraightout (Fig.H).
3. Insertlamp (MR-16bulb)between lampsprings.
4.AttachSOCKETto hi-pinprongson LAMP.
5. InsertLAMP RINGwith LAMP and GLASS LAMP GUARD back into ELBOW.
WARNING:
A.LAMPMANUFACTURERSREQUIRETHEGLASS
BEFOREENERGIZINGLAMP, AND THAT GREAT CARE MUSTBETAKEN
THAT LAMP IS FULLY COOLED BEFORE RELAMPING. AVOID FINGER
MARKSON INSIDEOFLAMPFORTHEYMAYCAUSESHORTLAMPLIFEAND
POSSIBLE BREAKAGE.
B.USEONLY REFLECTORTRIMS PROVIDEDBY LIGHTOLIERINC. USEOF
OTHERMANUFACTURER’SREFLECTORTRIMSVOIDSTHEUNDERWRfTERS
LABORATORIESLISTINGAND COULD CONSTITUTE A FIRE HAZARD.
NOTE:
1. LOW VOLTAGE FIXTURES should be dimmed only by specialdimmers intended specifically for that purpose. Use Lightolier,
Scenist, Crescendo VA, Neptune VA, Precision VA
variable autotransformers or electronic dimmers intended for use with low voltage fixtures.
2. Lowvoltage fixtures may produce audible sound when used with dimmers, which maybe objectionable in acoustically critical areas.
LAMPGUARDBEIN PLACE
EasysetVA,Sunrise VA, Radiant VA, or equivalent products by others or
w“T ““p
L
GIASS LAMP
GUARD
\
~ BAFFLE
Fig. H
APERTURE
Wwl
JUNCTIONBOX
I_
II
[
II
TRANSFORMER
PRIMARY120V.60
SECONDARY11.4V.
&5W.LOAO
3 21/32’
I
Hz
+—---- 5 29/32’ FIANGE DIA.—--+
Fig. I
Loading...