Lightolier Fluorescent Downlight and Wall Washer User Manual

—

INSTRUCTION SHEET NO.

INSTALLATION OF COMPACT FLUORESCENT

DOWNLIGHTS AND WALL WASHERS

IS:8054CL

0891 Page 1 of 2

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE. -

This fixture is intended for installation in accordance with the National Electrical Code and local

regulations. To assure full compliance with local codes and regulations,

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before
proceeding. This fixture is intended for ceiling mounting and is suitable for damp locations.

Retain these Instructions for maintenance reference. -

INSTALLATION OF DOWNLIGHT
A. INSTALL WHITE TRIM RING

NOTE

1. For overlappin trim installation (Fig. 1), slip WHITE TRIM RING

2. For flangeless trim installation (Fig. 4), WHITE TRIM RING is not

B. SNABIN

C. PUSH-UP REFLECTOR

1.

D. LAMPING

lnserI lamp, tip first through hole in side of reflector opposite lamp
SOCKETS. Bring lamp to horizontal position, line up pins, and push
into socket (Fig.8). To relamp, carefully pull straight out of socket, tilt
base downward, and remove lamp.

INSTALLATION OF LENS WALL WASHER AND OPEN

WALL WASHER

NOTE. aafore Installingreflector,make surethe mountingframe IS
Installedwith

(Fig. 10A or 10B).

Omit this sactlon If reflector is self-flenged.

over REFLEC#R, as shown in Fig. 2 and 3.

required.

Align TABS on SOCKET CUP with openings in REFLECTORand
push in SOCKET CUP until RETAINING SPRING snaps in (Fig. 5).

Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on
side opposite JUNCTION BOX. Pivot REFLECTOR and push it up
into ceiling (Fig. 6).

N~E To remove REFLECTOR, disengsge the SOCKET CUP by

depressing the RETAINING SPRING (Fig. 5). Turn REFLECTOR
counterolockwlse while pulling downward. After starting, use
both hands to ramov~ If desired. See Fig. 7.

JUNCTION BOX away from the wall to ba illuminated

REFLECTOR

OR LENS TRIM

check with your local electrical

@

FIG. 1

WHITE

TRIM

,,$y

.—.-

..

FIG. 2

..

/“

:: .:.

,4.,..,-.

.

@

RING

1

FIG. 3

Y.

,,. ..

FK3. 4

\

FOR OPEN WALL WASHER

Remove two RETAINING SPRINGS that are near the JUNCTION BOX from

1.

the MOUNTING FRAME (Fig 9).

Insert two new RETAINING SPRINGS, that are provided with the reflector

2.

trim, into pocket of MOUNTING FRAME (Fig. 9A).

3.

Then squeeze RETAINING SPRING into position with a plier (Fig. 9A).

RETAINING

SPRING

REMOVED

1 m

*

FIG. 9 FIG. 9A

FIG. 5

TO REMOVE

““E=Jum

v

wREFLEcTOR

FIG. 6 FIG.

SOCKET

/

n

—

—

.,5-;:::’;+’

‘..:>~’ ,, ,.

,, ,,,

,,,,,,

,.:,

~x.,:s

..

..+jf’

7

,.,,

,..

FIG. 8

lNSTALIATION OF COMPACT FLUORESCENT

DOWN LIGHTS AND WALL WASHERS (CONT’D)

;2;~54CL

Page 2 of 2

A. SNAPIN

Align TABS on SOCKET CUP with openings in reflector and push in
SOCKET CUP until RETAINING SPRING snaps-in (Fig. 5).

B. INSTALL WHITE TRIM RING

NOTE Omit this section If reflector is self-flanged.

1.For overlapping trim installation (Fig. 1) slip WHITE RING over

LENS TRIM as shown in Fig. 2 and 3.

2. For flangeless trim installation (Fig. 4), WHITE TRIM RING is not
required.

C. PUSH-UP REFLECTOR FOR LENS WALL WASHER

1. Tilt REFLECTOR and insert SOCKET CUP into ceiling opening on
side opposite JUNCTION BOX. Push REFLECTOR up leaving
approximately one inch of the REFLE~R exposed below the
CEILING LINE (Fia. 10A).

Compress TORSl~NTITE SPRINGS on LENS TRIM by squeezing

2.

with fingem. Insert into SLOTS in

REFLECTOR until flush with ceiling (Fig. 11).

NOTE To remove REFLEC70R, lift LENS and pull LENS TRIM down

(Fig. 12), then disengage the SOCKET CUP by daprsssing the
RETAINING SPRING (Fig.5). lhrn REFLECTOR counterclockwise
while pulling downward. Aftar stafling, use both hands to remove.
See Fig. 7.

REFLECTOR and push up into

PUSH-UP REFLECTOR FOR OPEN WALL WASHER

REFLECTOR and insert SOCKET CUP into ceiling opening on

1, Tilt

side opposite JUNCTION BOX. Pivot REFLECTOR and push it up
into ceilina [Fia. 13).

NOTE To remove REFLECTOR, disengage the SOCK~ CUP by
daprassing the RETAINING SPRING (Fig. 5). 7urn REFLEC70R
counteroiockwise while pulling downward. After starting, use
both hands to remove If dasired. Saa Fig. 7.

D. LAMPING

Line up pins and push into socket. To relamp, carefully pull lamp

straight out.

-.-,

CARE AND MAINTENANCE OF A12AK@ REFLECIOR

If handling of reflectors with anodized or Alzak finish is required, the
use of clean white or plastic film gloves is recommended to avoid
fingerprints.

Anodized or Alzak surfaces can be cleaned by the following methods

1.

Wipe off with a soft, clean, dry, lint-free cloth.

2.

Wipe off with a soft clean cloth dampened

solution. Rinse then wipe dry with lint-free cloth or paper towel.
Wipe off with a clean cloth dampened with a solution of wetting

3.

agent and water (such as 2 oz. per gallon “Pluronic L62-LF” by
Wyandotte Products). Then wipe dry.

4.

Or use a liquid wash such as Glass Wax”. Avoid gritty cleaning
agents.

in mild detergent

LENS WALL WASHER

SOCKET CUP

REFL LEAVE APPROX.

\

u“

WALL TO BE ILLUMINATED

r JUNCTION

BOX

1“ EXPOSED

TITE
G

M

FIG. 10A

OPEN WALL WASHER

JUNCTION

BOX

7

*K

--

WALL TO BE ILLUMINATED

FIG. 10B

~ b

SOCKET

CUP

/-- ‘“’%lON

-Qi-REFLEcTOR

13

FIG.

FIG. 11

FIG.

12