Lightolier Calculite Evolution Non-IC Airseal C3ALV Specification

Calculite® Evolution Non-IC Airseal

®

Frame-In Kit C3ALV

Page 1 of 1 3" Aperture, MR16 (12V)

8

9 5/8"

(245mm)

5" (127mm)

14 3/8"

(365mm)

Ceiling Cutout: 3-1/2” (89 mm) Dia.

For Complete Fixture Order: Trim Kit + Frame-In Kit. Each Sold Separately.

Frame-In Kit Lamp*

C3ALV
C3ALVE1
C3ALVE2

* Lamp wattage restriction: 65W for up to 1" thick ceiling, 50W for ceiling thickness greater than 1" (up to 2")

Note: Magnetic not recommended for residential or noise sensitive areas.

Magnetic 120V/277V
Electronic 120V
Electronic 277V

5" (127mm)

Plus Ceiling Thk.

42W-65W MR16 (12V)
20W-65W MR16 (12V)
20W-65W MR16 (12V)

5 1/2"

(140mm)

1/2" (13mm) Lip

Downlight

Open

Reflector

C3MRD

Series

2963 57

4

1

3" (76mm) Dia.

4" (102mm) Dia.

Trim Kit (See individual Trim Kit Specification Sheets)

Wall Washer

1 1/4"

Pinhole

C3MRPD

Series

Downlight

(Wet Loc.)

C3MRL

Series

Adjustable Accent

Cone Cone

(Wet Loc.)

C3MRA

Series

C3MRW

Series

1 1/4"

(Wet Loc.)

C3MRPA

Series

2" (59mm) Max.

Ceiling Thk.

Glasslite

Downlight

(Wet Loc.)

C3MRGD

Series

Glasslite

Adjustable

(Wet Loc.)

C3MRGA

Series

Features

1. Housing: Drawn, 0.036" (20 Ga.) steel. Matte black finish. Tight rigidly

built housing minimizes air leakage to less than 2 CFM at 1.57 PSF (or
75pa), which complies with Model Energy Code and Washington State
Energy Code and reduces heat loss and condensation in ceiling.

2. Mounting Frame: Die-formed, 0.036" (20 Ga.) steel, matte black finish.

1/2" deep integral lip. Four slots are positioned 90° apart to simplify

alignment.

3. Trim Kit Horizontal Adjustment Mechanism: Die-formed steel ring,

matte black finish. Provides 362° horizontal stop, lockable with Philips

screwdriver.

4. Thick Ceiling Ver tical Adjustment Mechanism: Adjustable trim kit

vertically to accommodate up to 2" thick ceiling, tool less and lockable.

5. Mounting Bars: Galvanized steel, 0.059" (#16 ga.). Bars pivot for easy

attachment and wire-in below ceiling line. Pre-installed telescoping
bars extend to accommodate 16" to 24" O.C. joist spacing. Bars can
accommodate 12" O.C. joist spacing after a slight field modification.
Integral nails for secure attachment to wood; at tach to T-bar ceilings with

out the need of accessories.

6. Lampholder: Procelain bi-pin socket. Pre-wired with No.18 AWG

Teflon leads.

7. Junction Box: 3-1/2" X 4" X 2-3/8" deep; 0.063" (#14 ga.) galvanized

steel. UL listed for maximum of (8) No. 12 AWG 90° C through branch
circuit conductors. Accessible from inside and outside of luminaire.
Outside J-Box door is hinged for maximum opening.

8. Thermal Protector: Meets NEC and UL requirements. Insulation must

be kept 3" away from any parts of the luminaire and must not be placed
above luminaire in a manner which will entrap heat.

9. Trim Kit: Order Separately. See individual trim kit specification sheets for

information.

Magnetic: 120V/277V 60 Hz. dual-voltage, core & coil. (Note: Magnetic not

recommended for residential or noise sensitive areas.) Electronic: 120V or
277V 50/60 Hz., regulated lamp volage, HPF, EMI and circuit protections, ther­mal auto-reset, quiet operation.

Dimming Controls: Use only dimmers specifically designed for use with
magnetic or electronic transformers. Consult Lightolier Control for informa-

tion. Low voltage luminaires may produce audible sound when used with dim­mers, which may be objectionable in acoustically critical areas.

Labels

U.L. (Suitable For Damp Locations), I.B.E.W.
Complies with Air Leakage Requirements as stated in the Model Energy Code
and the Washington State Energy Code.

Options and Accessories

Plaster Trim Ring (use with flangeless trim kit): CA3FMR

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:

Electrical:

Trans for mer: Replaceable from below; Transformer door rotates into fixture,

positioning transformer directly over aperture to allow one-handed removal

Lightolier a Genlyte company www.lightolier.com

631 Airport Road, Fall River, MA 02720 • [phone] • Fax [phone]

We reserve the right to change details of design, materials and finish.

© 2011 Genlyte Group LLC • E0711