Lightolier C7CW User Manual

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

INSTRUCTION SHEET NO.

IS:C7CW

A0604

Page 1 of 2

INSTALLATION PROCEDURE FOR: C7CW SERIES 7” DIA. H.I.D. WALL CYLINDER

USED WITH C7E17VM, C7E17OVM, C7P38MH, C7E17PL, C7E17FL SERIES FLANGLESS

REFLECTOR TRIM (ORDER SEPARATELY)

WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURERS’

REFLECTOR TRIMS MAY VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

CAUTION: For wet locations, in accordance with Underwriters Laboratories

requirements, a line of caulking compound such as acrylic or silicone must be
placed around the perimeter of CANOPY to seal water away from the
outlet box and back openings. Use only compatible REFLECTOR TRIMS
rated for use in Wet Locations.

INSTALLATION OF WALL CYLINDER TO OUTLET BOX
(Fig. 1, 2, 3, & 4)

STEP 1:

SCREWS.

STEP 2: Pass supply leads through opening in CANOPY and CLEAT.
STEP 3: Attach CANOPY and CLEAT to MOUNTING PLATE with (2) ¼-20

BOLTS (provided).

STEP 4: Make Connections. Bare Copper and/or green insulation wire(s)

must be connected to SUPPLY GROUND. Connect WHITE BALLAST LEAD
to NEUTRAL (WHITE) SUPPLY LEAD. Connect BLACK BALLAST LEAD to
HOT SUPPLY LEAD. Use wire nuts (local hardware items).

STEP 5: Install SET SCREWS loosely. Push excess supply leads back into

outlet box. Place cylinder over CLEAT and tighten (2) SET SCREWS.

INSTALLATION OF WALL CYLINDER TO POST OR OTHER
VERTICAL SURFACE MOUNTING (Fig. 2, 3 & 4)

1. CLEAT can also be mounted directly to any flat surface such as
MULLION. In this case, use of CANOPY is optional. Bring supply
leads through CLEAT and install CLEAT to wall. For wet locations, in
accordance with Underwriters Laboratories requirem ents, a line of
caulking compound such as acrylic or silicone must be placed around
the perimeter of EXTRUDED ARM to seal water away from the
wireway and back openings.

2. Proceed with Step 4 and 5 above.

INSTALLATION OF REFLECTOR TRIM TO CYLINDER (Fig. 4)

Follow installation instructions in Reflector Trim Instruction Sheet.

CAUTION:

Attach MOUNTING PLATE to outlet box with OUTLET BOX

 DO NOT ENERGIZE THE LAMP UNTIL
REFLECTOR TRIM IS COMPLETELY INSTALLED.

FIG. 4

MOUNTING PLATE
CANOPY

CLEAT

OUTLET BOX SCREWS

FIG. 3

1/4-20 BOLTS

MULLION

FIG. 2FIG. 1

A COMPANY

631 Airport Road, Fall River, MA 02720

GASKET

CLEAT

A

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

INSTRUCTION SHEET NO.

IS:C7CW

A0604

Page 2 of 2

INSTALLATION PROCEDURE FOR: C7CW SERIES 7” DIA. H.I.D. WALL CYLINDER

USED WITH C7E17VM, C7E17OVM, C7P38MH, C7E17PL, C7E17FL SERIES FLANGLESS

REFLECTOR TRIM (ORDER SEPARATELY)

WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURERS’

REFLECTOR TRIMS MAY VOID THE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

TO REPLACE BALLAST (Fig. 5 & 6)

Before changing the ballast, switch off the main power supply to the fixture.

STEP 1: Remove lamp.
STEP 2: Squeeze LAMPHOLDER SPRING while pushing

upward to disengage from REFLECTOR.
STEP 3: For cylinder with optional Auxiliary lighting, detach AUXILIARY

SSEMBLY SOCKET ASSEMBLY from REFLECTOR.

STEP 4: Remove WING NUTS, then separate UPPER HOUSING from top

of LOWER HOUSING to access BALLAST/PLATE ASSEMBLY.

STEP 5: Turn SCREW at SUPPORT BRACKET counterclockwise to loosen

SUPPORT BRACKET. Repeat with other (2) screws. Carefully remove
BALLAST/PLATE ASSEMBLY from UPPER HOUSING.

STEP 6: Replace BALLAST, capacitor and ignitor (magnetic type ballast).
STEP 7: Reattach BALLAST/PLATE ASSEMBLY to UPPER HOUSING by

tightening SCREWS until SUPPORT BRACKET locks onto UPPER
HOUSING. Repeat with other (2) screws.

STEP 9: Align STUDS with holes in LOWER HOUSING, then firmly tighten

with WING NUTS.

STEP 10: Reinstall REFLECTOR. For additional instructions (if needed),

see Reflector Trim Instruction Sheet.

FIG. 5

A COMPANY

631 Airport Road, Fall River, MA 02720