Lightolier C6CW User Manual
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
INSTRUCTION SHEET NO.
IS:C6CW
A0604
Page 1 of 2
INSTALLATION PROCEDURE FOR: C6CW SERIES 6” DIA. H.I.D. WALL MOUNT CYLINDER
USED WITH C6T6V SERIES FLANGLESS REFLECTOR TRIM (ORDER SEPARATELY)
WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURES’ REFLECTOR
TRIMS MAY VOID THE UNDERWRITERS LABRATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.
CAUTION: For wet locations, in accordance with Underwriters Laboratories
requirements, a line of caulking compound such as acrylic or silicone must be
placed around the perimeter of CANOPY to seal water away from the
outlet box and back openings.
INSTALLATION OF WALL CYLINDER TO OUTLET BOX
(Fig. 1, 2, 3, & 4)
STEP 1: Attach MOUNTING PLATE to outlet box with OUTLET BOX
SCREWS.
STEP 2: Pass supply leads through opening in CANOPY and CLEAT.
STEP 3: Attach CANOPY, CLEAT/GASKET to MOUNTING PLATE with (2)
¼-20 BOLTS.
STEP 4: Make Connections. Bare Copper and/or green insulation wire(s)
must be connected to SUPPLY GROUND. Connect WHITE BALLAST LEAD
to NEUTRAL (WHITE) SUPPLY LEAD. Connect BLACK BALLAST LEAD to
HOT SUPPLY LEAD. Use wire nuts (local hardware items).
STEP 5: Install SET SCREWS loosely. Place cylinder over CLEAT and
tighten (2) SET SCREWS.
INSTALLATION OF WALL CYLINDER TO POST OR OTHER
VERTICAL SURFACE MOUNTING (Fig. 2, 3 & 4)
STEP 1: CLEAT can also be mounted directly to any flat surface
such as MULLION. In this case, use of CANOPY is optional. Bring
supply leads through CLEAT and install CLEAT to wall. For wet
locations, in accordance with Underwriters Laboratories requirements,
a line of caulking compound such as acrylic or silicone must be
placed around the perimeter of EXTRUDED ARM to seal water away
from the wireway and back openings.
STEP 2: Proceed with Step 4 and 5 above.
INSTALLATION OF REFLECTOR TRIM TO CYLINDER (Fig. 4)
Follow installation instructions in Reflector Trim Instruction Sheet IS:C4T4V.
CAUTION:
DO NOT ENERGIZE THE LAMP UNTIL REFLECTOR
TRIM IS COMPLETELY INSTALLED.
INSTALL ONLY T-6 TUBULAR SINGLE-ENDED
CREAMIC ARC TUBE METAL HALIDE LAMP.
FIG. 1 FIG. 2
FIG. 3
MOUNTING PLATE
CANOPY
1/4-20 BOLTS
MULLION
CLEAT
OUTLET BOX SCREWS
FIG. 4
A COMPANY
631 Airport Road, Fall River, MA 02720
GASKET
CLEAT
A
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
INSTRUCTION SHEET NO.
IS:C6CW
A0604
Page 2 of 2
INSTALLATION PROCEDURE FOR: C6CW SERIES 6” DIA. H.I.D. WALL MOUNT CYLINDER
USED WITH C6T6V SERIES FLANGLESS REFLECTOR TRIM (ORDER SEPARATELY)
WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURES’ REFLECTOR
TRIMS MAY VOID THE UNDERWRITERS LABRATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.
TO REPLACE BALLAST (Fig. 5 & 6)
Before changing the ballast, switch off the main power supply to the fixture.
STEP 1: Remove APERTURE CONE ASSEMBLY from REFLECTOR
HOUSING by grasping inside of cone and pulling down.
STEP 2: Remove lamp.
STEP 3: Pull REFLECTOR HOUSING down until CLIPS stop at the bottom
lip of LOWER HOUSING. Press CLIPS inward to remove REFLECTOR
HOUSING.
STEP 4: Detach LAMPHOLDER from REFLECTOR HOUSING by
squeezing LAMPHOLDER SPRING.
STEP 5: Remove WING NUTS, then separate UPPER HOUSING from top
of Lower HOUSING to access BALLAST/PLATE ASSEMBLY.
STEP 6: Turn SCREW counterclockwise to lossen SUPPORT BRACKET.
Repeat with other (2) screws. Carefully remove BALLAST/PLATE
SSEMBLY from UPPER HOUSING.
STEP 7: Detach BALLAST SUPPORT BRACKET by removing (2)
BALLAST SUPPORT BRACKET SCREWS.
STEP 8: Replace BALLAST. Reattach BALLAST/BALLAST SUPPORT
BRACKET, BALLAST/PLATE ASSEMBLY to UPPER HOUSING.
STEP 9: Align STUDS with holes in LOWER HOUSING, then tighten firmly
with WING NUTS.
STEP 10: Reverse installations from Step 4 to Step 1. For additional
instructions if needed, see Reflector Trim Instruction Sheet IS:C4T4V.
TO REPLACE LAMP (Fig. 5 & 6)
Before replace the lamp, switch off the main power supply to the fixture.
STEP 1: Remove APERTURE CONE ASSEMBLY from REFLECTOR
HOUSING by grasping inside of cone and pulling down.
STEP 2: Replace lamp. Follow lamp manufacturer’s directions for proper
care and handing of lamp.
STEP 3:
Replace cone into reflector housing.
FIG. 5
APERTURE CONE
ASSEMBLY
A COMPANY
631 Airport Road, Fall River, MA 02720
Loading...