Lightolier C4ALV User Manual

Calculite® Evolution Non-IC Airseal

123 4567

1/2" (13mm) Lip

Vertical Adjustment
1" (25mm)
to 2 3/4" (70mm)

.875" Max (28mm)

Ceiling Thickness

5" (127mm)

Plus Ceiling Thk.

5 1/2"

(140mm)

9 5/8"

(245mm)

5" (127mm)

14 3/8"

(365mm)

Ceiling Cutout: 5 1/16" (129 mm) Dia.

®

Frame C4ALV

Page 1 of 1 4" Aperture, MR16 (12V)

For Complete Fixture Order: Trim Kit + Frame-In Kit. Each Sold Separately.

Frame-In Kit Reflector Trim

C4ALVMU

Magnetic 120V/277V

C4ALVE1

Electronic 120V

Note: Magnetic transformers may produce audible sound when used with dimmers, which may be objectionable in acoustically critical areas.

Open
Downlight

C4MRD

42W-75W
MR16 (12V)

Adjustable

Accent

C4MRA

42W-75W
MR16 (12V)

Adjustable
2" Aperture

C4MR2

42W-75W
MR16 (12V)

Adjustable
1 1/4" Pinhole

C4MRP

42W-75W
MR16 (12V)

Lensed
Wall Washer

C4MRL

42W-75W
MR16 (12V)

Glasslyte

Downlight

C4MRGD

42W-75W
MR16 (12V)

Glasslight
Adjustable

C4MRGA

42W-75W
MR16 (12V)

Lensed

Adjustable

C4MRW

42W-75W
MR16 (12V)

Features

1. Housing: Drawn, 0.036" (20 Gauge) steel. Matte black finish. Housing

minimizes air leakage to less than 2 CFM (Cubic Feet per Minute) at 1.57
PSF (Pounds per Square Foot) (or 75 Pascals), which complies with Model
Energy Code and Washington State Energy Code and reduces heat loss and

condensation in ceiling.

2. Mounting Frame: Die-formed, 0.036" (20 Gauge) steel, matte black finish.

Four slots are positioned 90° apart to simplify alignment.

3. Retaining Springs: Steel springs secure reflector trim to mounting frame

for tool-less installation.

4. Mounting Bars: Galvanized steel, 0.059" (16 Gauge). Bars pivot for

attachment and wire-in below ceiling line. Pre-installed telescoping bars
extend to accommodate 16" to 24" on center joist spacing. Integral screws
for secure attachment to wood; at tach to T-bar ceilings without the need for

accessories.

5. Lampholder: Porcelain bi-pin socket. Pre-wired with Teflon leads.

6. Junction Box: 3-1/2" X 4" X 2-3/8" deep; 0.063 (14 Gauge) galvanized

steel. UL listed for maximum of (4) No. 12 AWG (American Wire Gauge) 90°
C through branch circuit conductors. Accessible from inside and outside
luminaire. Outside J-Box door is hinged for maximum access.

7. Thermal Protector: Meets NEC and UL requirements. Insulation must be

kept 3" away from any part of the luminaire and must not be placed above
luminaire in a manner which will entrap heat.

Electrical:

Transformer: Replaceable from below; transformer door rotates into fixture,

positioning transformer directly over the aperture. Magnetic: 120V/277V 60Hz.
dual-voltage, core & coil. Electronic: 120V or 277V 50/60 Hz., regulated lamp
voltage, HPF (High Power Factor), EMI (Electro Magnetic Interference) and shor t
circuit protections, thermal auto-reset, quiet operation.

Electrical (cont.)

Dimming Controls: Use only dimmers specifically designed for use with

magnetic or electronic transformers. Consult Lightolier Controls division for
information. Low voltage luminaries may produce audible sound when used with

dimmers.

Accessories

Thick Ceiling Adapter: for .875" - 1.75" thick ceiling capability, utilize C47CA2

Labels

CULUS (Suitable For Damp Locations), U.S. & Foreign Patents pending. Complies
with Air Leakage Requirements as stated in the Model Energy Code and the
Washington State Energy Code.

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):
Notes:

Lightolier is a Philips group brand

631 Airport Road, Fall River, MA 02720 • [phone] • Fax [phone]

We reserve the right to change details of design, materials and finish.

www.lightolier.com © 2008 Philips Group • F0708