Lightolier A0497 User Manual
4. Tighten LOCKING SCREW. Don’t over tighten.
5. Splice SUPPLY WIRESto existing wires in OUTLET BOX.
BLACK WIRE or wire without tracer mark from box to BLACK
SUPPLY LEAD. WHITE WIREor wire with tracer mark to
WHITE SUPPLY WIRE.
NOTE: The length of the SUPPLY WIRE must be sufficient to
wire the ELECTRICAL CONNECTOR.
6. Mount CROSSBAR to OUTLET BOX using
MOUNTING SCREWS while passing SUPPLY
WIRES through center hole of CROSSBAR.
7. Thread the two NUTS onto one end of the STEM.
8. Slide WIRE COVER and CANOPY COVER onto STEM.
9. Pass SUPPLY WIRE through STEM and thread STEM into
CROSSBAR.
10. Attach SUPPLY GROUND WIREto
GROUND SCREW on CROSSBAR.
11. Hang TRACK by sliding the BRACKET over
the LOWER NUT.
12. Tighten the NUT against the BRACKET.
13. Slide CANOPY against the ceiling and secure by tightening
the CANOPY SCREW.
14. Push WIRE COVERonto BRACKET and secure to ELECTRICAL
CONNECTORusing COVER SCREW.
15. Follow instructions included with the ELECTRICAL CONNECTOR
when wiring the ELECTRICAL CONNECTOR.
INSTRUCTION SHEET NO.
IS:9187
A0497 Page 1 of 1
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
STEM WIRE COVER FOR USE WITH 9100 SERIES,
RADIUS
®
TRACK SYSTEMS ONLY
WARNING
• DO NOT WALL MOUNT STEM.
• DO NOT CUT THE STEM TUBE.
• DO NOT MOUNT STEM TO ELECTRICAL CONNECT ORS OR ANY TRACK JOINTS .
• USE WIRE COVER TO FEED POWER INTO CONNECTORS: 9184WH, BK; 9147WH, BK;
9155WH, BK; 9150WH, BK; OR 9151WH, BK.
• USE WIRE COVER WITH STEM KITS 9184WH, BK; 9185WH, BK; OR 9186WH, BK.
• USE WIRE COVER WITH A 3” OR 4” OCT AGON OUTLET BOX.
• USE SOLID 12GA. COPPER WIRE WITH STEM WIRE COVER.
®
FALL RIVER, MASSACHUSETTS 02720
MONTREAL, QUEBEC, CANADA
®
CAUTION: ENSURE THAT THE WIRE COVER EXTENDS
TO THE END OF THE ELECTRICAL CONNECTOR BEFORE
TIGHTENING THE BRACKET
1. Install ELECTRICAL CONNECTORinto the TRACK UNIT following
the instructions included with the electrical connector. (Stem kit
sold separately).
2. Mark centerline through center of OUTLET BOXto locate track
and stem center location.
3. Attach BRACKETto existing hole in the TRACK using the
BRACKET SCREW and ACORN NUT.
3” OR 4” OC TAGONAL BOX
OUTLET BOX (BY O THERS)
SUPPLY WIRES
(BY O THERS)
CROSSBAR
MOUNTING
SCREWS
GROUND
SCREWS
CANOPY
CANOPY
SCREW
BRACKET
COVER
(DISCARD)
FROM 9184,
9185, 9186
STEM
NUT
BRACKET
LOCKING
SCREW
TRACK UNIT
(SOLD
SEPA RATE LY)
ACORN NUT
BRACKET SCREW
ELECTRICAL CONNECTOR
(SOLD SEPA RATE LY )
L OWER NUT
COVER SCREW
WIRE COVER
Loading...