A
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
INSTRUCTION SHEET NO.
IS:7784
A0302
Page 1 of 3
INSTALLATION PROCEDURE FOR ELLIPSOIDAL DOWNLIGHT (A-LAMP)
CAUTION: (RISK OF FIRE) DO NOT INSTALL INSULATION ABOVE, NOR WITHIN 3 INCHES (76mm) OF ANY PART OF
THE LUMINAIRE.
FIG. 1
A. INSTALL MOUNTING FRAME IN CEILING USING ADJUSTABLE
(1) With MOUNTING BARS (order separately):
18” – Cat. No. 1950; 27” – Cat. No 1951).
Use rectangular slots as shown.
(2) With ¾” channel (by others)
FIG. 3 FIG. 2 FIG. 4
Slide MOUNTING BARS or CHANNELS (by others) through slots in ADJUSTABLE MOUNTING BRACKET which will place the
bottom of the MOUNTING FRAME approximately in line with the finished ceiling line. Final adjustments may be made by means of
MOUNTING BRACKET SCREWS on inside of fixture.
For wood joist construction: TELESCOPING
MOUNTING BARS No. 7994 (order separately) may be
used to secure MOUNTING FRAME (Fig.5).
TELESCOPING
MOUNTING BARS
For suspended ceilings:
CCESSORY No. 1956 (order separately) may be used
with 18” or 27” MOUNTING BARS or TELESCOPING
MOUNTING BARS for quick mounting (Fig. 6) or simply
wire MOUNTING BARS to ceiling members (Fig. 7)
MOUNTING
BAR
(3) With 1 ½” channel (by others)
T-Bar ANCHOR CLIPS
T-BAR ANCHOR
CLIPS
ACCESSORY
MOUNTING
BAR
FIG. 5
FIG. 6
FIG. 7
A COMPANY
631 Airport Road, Fall River, MA 02720
INSTRUCTION SHEET NO.
IS:7784
A0302
NOTE: To insure proper installation it is important that MOUNTING FRAME always be
securely mounted to structural ceiling members.
Page 2 of 3
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
B. INSTALL AND WIRE
1) Install fixture in ceiling. Adjust fixture for proper alignment with
the ceiling (Step A) and then wire fixture. White fixture lead to
neutral supply lead. Bare fixture wire to supply ground. Use wirenuts (local hardware items). Place all electrical connections in
the J-BOX. Attach J-BOX COVER onto J-BOX.
NOTE: SLIDE LATCHES permit removal of reflector from
within fixture for access to splices or for relamping from
above ceiling (Fig. 8) These latches must be snapped
back into position to prevent reflector from disengaging
during relamping.
FIXTURE
C. PUSH-IN (FIG.8)
1) Push APERTURE CONE or MULTI-GROOVE BAFFLE
straight up into MOUNTING FRAME until tight against
finished ceiling. RETAINING SPRINGS on MOUNTING
FRAME (Fig.1) will secure APERTUR CONE or MULTIGROOVE BAFFLE in place.
NOTE: To remove CONE or BAFFLE, turn CONE or
BAFFLE counterclockwise while pulling downward.
After starting, use both hands to remove, if desired.
See (Fig. 11)
FIG. 8
FIG. 10
FIG. 9
TO REMOVE
A COMPANY
631 Airport Road, Fall River, MA 02720
INSTRUCTION SHEET NO.
A
IS:7784
A0302
Page 3 of 3
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
D. ACCESS TO JUNCTION BOX FROM BELOW
1) Switch off power to fixture at service panel.
2) Remove CONE (Fig. 11) and LAMP.
3) Locate SLIDE LATCH on HOUSING SUPPORT push
out to the right to disengage SLIDE LATCH from
SLOT of REFLECTOR (Fig. 12). Repeat for other two
latches.
4) Push RFLECTOR up and to the side to provide
access to JUNCTION BOX. (Fig. 12).
5) To access JUNCTION BOX, lift up JUNCTION BOX
SPRING to remove JUNCTION BOX DOOR (Fig. 12).
6) After servicing, push all wires back inside JUNCTION
BOX. Insert TABS of JUNCTION BOX DOOR into
slots of JUNCTION BOX and align NOTCH of
JUNCTION BOX DOOR with JUNCTION BOX
SPRING. Snap JUNCTION BOX DOOR onto
JUNCTION BOX firmly (Fig. 12 and 13). Make sure
JUNCTION BOX DOOR is not pinching wires.
7) Install REFLECTOR back into HOUSING SUPPORT
(Fig. 13). For easier installation, the conduit from
socket to junction box should be positioned as shown
in Fig. 13.
8) Feel through the slots to align SLOTS of
REFLECTOR with SLIDE LATCHES. Note: SLIDE
LATCHES may not be visible from below, it is
recommended to first align the slot with the latch
opposite to junction box, then place REFLECTOR on
inside of HOUSING SUPPORT (Fig. 13).
9) Slide SLIDE LATCH to the left and pull back to
secure REFLECTOR (Fig. 13). Repeat for the other
two latches.
10) To ensure REFLECTOR is properly secured, rotate
REFLECTOR slightly to ensure SLIDE LATCHES
engage with SLOTS in REFLECTOR. The
REFLECTOR should not rotate if it is in locked
position.
11) Install lamp.
12) Install CONE (Step C PG 2)
REFLECTOR
REFLECTOR
SLOT
HOUSING SUPPORT
REFLECTOR
SLOTS
SLIDE LATCH
JUNCTION BOX
JUNCTION BOX
DOOR
FIG. 12
JUNCTION BOX
SPRING
TAB
E. CARE AND MAINTENANCE OF “ALZAK”
REFLECTOR
If handling of reflectors with anodized or Alzak finish is
required, the use of clean white or plastic film gloves is
recommended to avoid fingerprints.
nodized or Alzak surfaces can be cleaned by the
following methods:
1) Wipe off with a soft, clean, dry, lint-free cloth.
2) Wipe off with a soft, clean cloth dampened in mild
detergent solution. Rinse, then wipe dry with a lintfree cloth or paper towel.
3) Wipe off with a clean cloth dampened with a solution
of wetting agent and water (such as 2 oz. per gallon)
“Pluronic L62-F” by Wyandotte Products). Then wipe
dry.
4) Or use a liquid wash such as Glass Wax
gritty cleaning agents.
. Avoid
HOUSING SUPPORT
SLIDE LATCHES
FIG. 13
A COMPANY
631 Airport Road, Fall River, MA 02720
Loading...