Lightolier A0200 User Manual

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION FOR INSTALLATION OF PRE-WIRED COMPACT FLUORESCENT

EMERGENCY LIGHTING DECORATIVE SURFACE UTILITY FIXTURES

INSTRUCTION SHEET NO.

IS:EMSU

Page 1 of 3A0200

WARNING: (RISK OF FIRE)

5242PB326UE, 5243SA326UE, 5243SB326UE, 5543PB326UE AND 5543WH326UE. MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED FOR 60˚.

SUPPLY WIRING MUST BE RATED 90˚C. WHEN INSTALLING THE FOLLOWING MODEL NUMBERS ONLY: 5240WH326UE, 5241WH326UE,

CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLATION.

NOTICE: THIS INSTRUCTION SHEET TO BE USED IN CONJUNCTION WITH INSTRUCTIONS

SUPPLIED FOR THE INSTALLATION OF SPECIFIC MODEL BEING INSTALLED.

IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING:

1. Turn off AC power before proceeding.

2. Be sure all electrical connections are complete and outlet box is closed before battery connectors on emergency pack

are connected.

3. Do not use outdoors.

4. Do not mount near gas or electrical heaters.

5. Do not attemp to service the battery. A sealed, rechargeable, no maintance battery is used. Do not incinerate or mutilate;

may burst or release toxic materials. Do not short circuit; may cause burns. Battery acid can cause burns to skin and
eyes. If acid is spilled on skin or eyes, flush with fresh water and contact a physician immediately.

6. Equipment should be mounted in locations and at a height where it will not be readily subject to tampering by unauthorized
personnel.

7. The use of accessory equipment is not reccommended by the manufacturer and may cause an unsafe condition.

8. Do not use the equipment for other than intended use.

9. This unit has more than one power supply connection piont. To reduce the risk of electrical shock, disconnect both the

normal and the emergency power supplies before servicing.

10. Before servicing to prevent electrical shock, disconnect the battery connectors on the emergency pack (located on the

end of the emergency pack). Make certain that the switch (if the fixture is switched) and the unswitched lines to the

emergency pack are turned off at the fuse box. Servicing should be performed by qualified personnel only.

INSTALLATION

WARNING: TO PREVENT HIGH VOLTAGE ON THE RED & YELLOW OUTPUT LEADS PRIOR TO

INSTALLATION, BATTERY CONNECTOR MUST BE OPEN. DO NOT JOIN BATTERY CONNECTOR UNTIL

INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED TO THE EMERGENCY BALLAST.

A. WIRING -

1. Make sure AC power is off at fuse box.

2. Make sure that the necessary branch circuit wiring is available.

An unswitched source of power is required for the emergency pack.

3. The emergency pack must be fed from the same branch circuit as the AC ballast(s).

4. In switched fixtures, emergency pack must be connected ahead of any local switching.

5. Be sure all electrical connections are made and outlet box is closed before battery

connectors on emergency pack are connected.

6.

Select the appropriate wiring diagram to connect the emergency pack and the AC ballast: (See Pages 2 & 3)

Read and understand all instructions before proceeding.

LIGHTOLIER a GENLYTE THOMAS company.

631 Airport Road, Fall River, MA 02720

INSTRUCTION SHEET NO.

IS:EMSU

Page 2 of 3A0200

INSTRUCTION FOR INSTALLATION OF PRE-WIRED COMPACT FLUORESCENT

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector
before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

EMERGENCY LIGHTING DECORATIVE SURFACE UTILITY FIXTURES

WIRING DIAGRAM A

(2-Lamp 13W OR 26W 4 Pin Quad Tube
Pre-Wired for 120V or 277V)
(TWO EMERGENCY LAMPS ON)

NOTE: FOR UNSWITCHED CIRCUIT, CONNECT
120V OR 277V EMERGENCY PACK HOT
LEAD TO AC BALLAST HOT LEAD.

BATTERY

CONNECTOR

WHITE

INDICATOR
LIGHT

VIOLET +

BROWN -

WIRING DIAGRAM B

(2-Lamp 39W 4 Pin Twin Tube
Pre-Wired for 120V)
(TWO EMERGENCY LAMPS ON)

NOTE: FOR UNSWITCHED CIRCUIT, CONNECT

120V EMERGENCY PACK HOT

LEAD TO AC BALLAST HOT LEAD.

BATTERY

CONNECTOR

WHITE

INDICATOR
LIGHT

VIOLET +

BROWN -

RED

RED

EMERGENCY

BALLAST

EMERGENCY

BALLAST

CAP UNUSED

LEAD

120V (BLK) OR
277V (ORG)

120V (BLK) OR 277V (ORG)

(COM) WHITE

BLUE/WHITE

BLUE

YELLOW

YEL/BLK

RED

277V
(ORG)

120V (BLK)

(COM) WHITE

BLUE/WHITE

BLUE

YELLOW

YEL/BLK

RED

UNUSED
CAPPED

(UNSWITCHED)

TEST

SWITCH

SKT

(UNSWITCHED)

SWITCH

JMPR 2

TEST

JMPR 1

RED

JMPR 1

JMPR 2

RED

BLK

BLK

BLK

BLK

WHITE

WHITEWHITE

SKT

SKTSKT

(SWITCHED OR UNSWITCHED)

HOTCOMHOT

GRD

GREEN

BLACK

WHITE

BLUE

BLUE

YEL A

YEL B

RED

RED

RED

(SWITCHED OR UNSWITCHED)

HOTCOMHOT

GRD

GREEN

BLACK

WHITE

BLUE

BLUE

YEL A

YEL B

RED

RED

RED

AC

BALLAST

AC

BALLAST

WIRING DIAGRAM C

(2-Lamp 39W 4 Pin Twin Tube
Pre-Wired for 277V)
(TWO EMERGENCY LAMPS ON)

NOTE: FOR UNSWITCHED CIRCUIT, CONNECT

277V EMERGENCY PACK HOT
LEAD TO AC BALLAST HOT LEAD.

BATTERY

CONNECTOR

INDICATOR
LIGHT

VIOLET +

BROWN -

RED

WHITE

EMERGENCY

BALLAST

120V
(BLK)

277V (ORG)

(COM) WHITE

BLUE/WHITE

BLUE

YELLOW

YEL/BLK

RED

UNUSED
CAPPED

HOT

(UNSWITCHED)

TEST
SWITCH

BLK

BLK

JMPR 1

(SWITCHED OR UNSWITCHED)

HOTCOM

GRD

GREEN

BLACK

WHITE

BLUE

BLUE

YEL A

YEL B

RED

RED

RED

SKTSKT

JMPR 2

RED

LIGHTOLIER a GENLYTE THOMAS company.

631 Airport Road, Fall River, MA 02720

AC

BALLAST