Lightolier 8292 User Manual
INSTRUCTIONS FOR ATTACHING ADAPTER TO SINGLE
CIRCUIT LYTESPAN TRACK:
1. Position LEVER as shown in Fig. 1.
2. Align GROOVE in ADAPTER with BEAD on TRACK. See Fig. 1.
(If GROOVE of ADAPTER is not placed over BEAD in
TRACK, a potential hazard may result.)
3. Insert ADAPTER into TRACK.
4. Rotate LEVER 90° while pushing upward on ADAPTER, to
make mechanical and electrical connection. See Fig. 2.
To remove or change fixture location on the TRACK, reverse
procedure #4 above.
INSTRUCTIONS FOR CONVERTING POWERARC ATTACHMENT
FITTING TO OPERATE ON 2 CIRCUIT LYTESPAN TRACK:
NOTE: To insure proper operation of POWERARC on Two
Circuit Lytespan Track, the BLACK SPACER (provided)
must be used at all times on the plug assembly. The
BLACK SPACER is not used when operating
POWERARC on Single Circuit Track.
LOWER CIRCUIT, Fig. 3 & 6:
Illustrates contacts in low position with spacer in place for
lower circuit.
UPPER CIRCUIT, Fig. 4, 5, & 6:
To convert attachment fitting for upper circuit, raise BRASS
CONTACT to high position (as indicated by dotted line) by
pulling CONTACT as high as stop permits and slipping on
BLACK SPACER as shown in Fig. 4 & 5.
Do not try to move stationary silver contact.
AIMING ADJUSTMENTS:
CAUTION: ALLOW TIME FOR FIXTURE TO COOL BEFORE
MAKING ANY ADJUSTMENTS!
Rotate fixture both HORIZONTALLY and VERTICALLY to the
desired position. Fixture has horizontal and vertical rotation
stops (DO NOT FORCE FIXTURE PAST STOPS. DOING SO MAY
CAUSE AN ELECTRICAL HAZARD) See FIG. 7. For precise
VERTICAL rotation, rotate HEAD of fixture and line up desired
angle on the AIMING ANGLE INDICATOR with the INDICATOR
TAB (See FIG. 8).
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:8292
0203 Page 1 of 2
INSTRUCTIONS FOR THE OPERATION AND ATTACHMENT OF POWERARC™TO A
LYTESPAN
®
TRACK SYSTEM. FOR USE WITH LYTESPAN TRACK SYSTEMS ONLY.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
®
HORIZONTAL
ROTATION
FIG. 7
VERTICAL
ROTATION
FIG. 8
AIMING
ANGLE
INDICATOR
INDICATOR
TAB
HEAD
FIG. 1
LEVER
ADAPTER
GROOVE
BEAD
TRACK
ADAPTER
LEVER IN
ENERGIZED POSITION
FIG. 2
ADAPTER
FIG. 3
MOVABLE
BRASS
CONTACT
BLACK
SPACER
PLUG
ASSEMBLY
ADAPTER
PLUG
ASSEMBLY
STATIONARY
CONTACT
(Common)
MOVABLE
BRASS
CONTACT
FIG. 4
BLACK
SPACER
MOVABLE
BRASS
CONTACT
BLACK
SPACER
PLUG
ASSEMBLY
ADAPTER
FIG. 5
UPPER
CIRCUIT
LOWER
CIRCUIT
Common
FIG. 6
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:8292
0203 Page 2 of 2
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
®
INSTRUCTIONS FOR OPERATING AND LAMPING A POWERARC FIXTURE
INSTRUCTIONS FOR LAMPING A POWERARC FIXTURE:
1. Turn off power to fixture.
2. Remove the LENS by inserting finger into SLOT A and
pressing the LENS in the direction of SLOT B (See FIG. 9).
3. Carefully rotate LENS out of SLOT A in the direction shown
in FIG. 10.
4. Slide glass out of SLOT B by pulling the LENS in the
direction of SLOT A (See FIG. 11).
5. To insert LAMP (70W CDM or CMH T-6 Double Ended
Metal Halide M85), carefully push one end of the LAMP
CONTACT into one end of the SOCKET CONTACT until
the other end of the LAMP can be inserted into the
opposite SOCKET (See FIG. 12).
WARNING: ACCORDING TO MANUFACTURER’S
INSTRUCTIONS, LAMP SHOULD BE INSERTED
IN THE SOCKET WITH A MINIMUM ANGLE
OTHERWISE BENDING FORCES WILL RESULT IN
LAMP BREAKAGE. ALSO, INSTALL LAMP USING
PROTECTIVE PAPER AND DO NO REMOVE IT
UNTIL INSTALLATION IS COMPLETE. IF LAMP IS
TOUCHED WITH BARE HANDS, CLEAN LAMP
WITH DENATURED ALCOHOL AND WIPE WITH
LINT FREE CLOTH.
6. Insure both LAMP CONTACTS are properly seated into the
SOCKET CONTACTS (See FIGS. 12 & 13).
7. To re-insert LENS: First insert LENS in SLOT A (side with no
switch), carefully push the LENS until you can set it flat into
the face of the fixture. Make sure it presses the INTERRUPT
SWITCH, then engage LENS into SLOT B.
WARNING: IF USED IMPROPERLY, THIS LAMP
CAN CAUSE SERIOUS SKIN BURN AND EYE
INFLAMMATION FROM SHORTWAVE ULTRAVIOLET RADIATION. DO NOT OPERATE FIXTURE
WITHOUT PROTECTIVE LENS IN PLACE. FIXTURE
IS EQUIPPED WITH A POWER INTERRUPT SWITCH
TO PREVENT LAMP FROM BEING ENERGIZED
WHEN LENS IS REMOVED (SEE FIG. 9). DO NOT
ATTEMPT TO DISABLE THIS DEVICE.
SLOT A
LENS
LENS
SLOT A
FIG. 9
POWER
INTERRUPT
SWITCH
SLOT B
LENS
SLOT B
FIG. 11
SOCKET
SOCKET
CONTACT
FIG. 10
FIG. 12
SOCKET
LAMP
LAMP
CONTACT
LAMP
FIG. 13
Loading...