READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local
regulations. To assure full compliance with local codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:8228
0499 Page 1 of 2
INSTRUCTIONS FOR FIXTURES 8228, 8238, 8248, 8582, 8583, 8595, & ACCESSORIES
INSTRUCTIONS FOR ASSEMBLING PAR-TECH®RING SHADES TO PAR-TECH &
METALLICS
TM
FIXTURES FOR USE WITH LYTESPAN®OR PROSPEC® TRACK SYSTEMS ONLY.
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
®
TO INSTALL RING SHADE:
1. Line up shade’s NECK FLANGE with corresponding
openings at inside diameter of ARM.
2. Push in and twist-lock RING SHADE by turning in clockwise until it is tightly held.
3. Install indicated PAR lamp into shade
(see LAMPING INFORMATION on page 2).
TO INSTALL ACCESSORIES INTO RING SHADES:
NOTE: RING SHADE plus an ACCESSORY HOLDER are required
to install ACCESSORIES into fixtures. (The ACCESSORY HOLDERS are sold separately from the SHADES). For ACCESSORY
information see ACCESSORIES chart on page 2. ACCESSORY
HOLDER may be used without ACCESSORIES.
1. Before installing ACCESSORY HOLDER, assemble RING
SHADE to the Par-Tech or Metallics fixture and install
lamp (See above).
2. Place the desired ACCESSORIES inside ACCESSORY
HOLDER (A max. of two ACCESSORIES). Line up
ACCESSORY HOLDER so that the SPRINGS are facing the
inside diameter of the RING SHADE. Push ACCESSORY
HOLDER into shade until it snaps into the GROOVE
(See Fig. 3 & 4).
RING SHADE
NECK FLANGE
ARM
FIXTURE ADAPTERS:
8201 & 8202
SPRINGS
ACCESSORY
HOLDER
GROOVE
ACCESSORIES
optional (sold separately)
SPRINGS
ACCESSORY
HOLDER
GROOVE
ACCESSORIES
optional (sold separately)
Fig. 1
Fig. 2
Fig. 3
Fig. 4
FIXTURE ADAPTERS:
8701, 8704E, 8705E, 8706E,
8707E, 28701, & 28705E
ARM
NECK FLANGE
RING SHADE
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local
regulations. To assure full compliance with local codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:8228
0499 Page 2 of 2
INSTRUCTIONS FOR FIXTURES 8228, 8238, 8248, 8582, 8583, 8595, & ACCESSORIES
INSTALLATION INSTRUCTIONS FOR RELAMPING PAR-TECH®& METALLICS
TM
FIXTURES WITH
RING SHADES. FOR USE WITH LYTESPAN
®
OR PROSPEC® TRACK SYSTEMS ONLY.
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
®
Relamping RING SHADES:
CAUTION: TURN OFF FIXTURE AND ALLOW
TO COOL BEFORE RELAMPING OR MAKING
ADJUSTMENTS.
1. If ACCESSORY HOLDER (sold separately) is present,
pull out evenly until it snaps out of the shade
(See Fig. 5 & 6).
2. Remove lamp by rotating counter clockwise.
3. Install indicated PAR lamp (see LAMPING INFORMATION
chart below).
4. To replace ACCESSORY HOLDER, see page 1.
SHADE
ACCESSORY
ACCESSORY
HOLDERS
(2 FILTERS MAX.)
COLOR
FILTERS
DIFFUSION/
SPECIAL
FILTERS
HEX CELL
LOUVERS
PAR20 RING SHADE (8228)
8582
AF25 RD, BL, GR, MM, BG, YG,
MA, SP, LS, SB, BA, DA, LP
AF25 UV, PF, SY, LF, AS
AL25HC
PAR30 RING SHADE (8238)
8583
AF3 RD, BL, GR, MM, BG, YG,
MA, SP, LS, SB, BA, DA, LP
AF3 UV, PF, SY, LF, AS
AL3HC
PAR38 RING SHADE (8248)
8595
AF4 RD, BL, GR, MM, BG, YG,
MA, SP, LS, SB, BA, DA, LP
AF4 UV, PF, SY, LF, AS
AL4HC
ACCESSORIES
CATALOG NUMBER LAMP TYPE
8228WH,BK,TM,NM
(PAR20 Ring Shade)
8238WH,BK,TM,NM
(PAR30 Ring Shade)
8248WH,BK,TM,NM
(PAR38 Ring Shade)
PAR20 50W MAX.
PAR30 75W MAX.
PAR38 250W MAX.
150W MAX. with accessories,
(with fixture 8701)
or
PAR38 150W MAX.
(with fixtures 8201, 8202)
PAR20 39W (with fixture 8704E)
PAR30L 39W (with fixture 8704E)
PAR30L 70W (with fixture 8705E & 28705E)
NO ACCESSORIES
PAR38 70W (with fixture 8706E)
PAR38 100W (with fixture 8707E)
Incandescent/Halogen Metal Halide
Fig. 5
Fig. 6
ACCESSORY HOLDER
(sold separately
form shades)
ACCESSORY HOLDER
(sold separately
form shades)
Loading...