Lightolier 8021DW User Manual
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local
regulations. To assure full compliance with local codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:8021DW
A0399 Page 1 of 2
INSTALLATION OF CALCULITE COMPACT FLUORESCENT
DOUBLE & CORNER WALL WASHER TRIMS.
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
®
1. FRAME-IN
See Frame-In-Kit Instruction Sheet for
installation instructions.
2. REMOVE PRE-INSTALLED SPRINGS
Use pliers to remove all 4 springs on FRAME
(Fig.1)
3. SNAP-IN-SOCKET HOUSING
Engage RETAINING SPRING into SLOT of
REFLECTOR NECK (Fig. 2). NOTE: Refer to label
on inside of REFLECTOR NECK for proper lamping
position. See Frame-In-Kit for lamp information.
4. INSTALL SOCKET HOUSING ASSEMBLY
Pass SOCKET HOUSING ASSEMBLY through
aperture opening of FRAME as shown in (Fig. 3).
5. SNAP-IN-SOCKET HOUSING ASSEMBLY TO
FRAME
a) Align side legs of SOCKET HOUSING ASSEM-
BLY with vertical MOUNTING SUPPORTS on
either side of FRAME.
b) Snap prongs on bottom of side legs into slot on
FRAME until SOCKET HOUSING ASSEMBLY is
secure to FRAME (Fig. 4).
6. INSTALL KICK REFLECTORS
We recommend using clean white or plastic film
gloves when installing reflectors to avoid fingerprints.
a) Align SLOT in top portion of KICK REFLECTOR
with CLIP on RING (Fig. 5).
b) Repeat for second KICK REFLECTOR.
REFLECTOR NECK
SOCKET CUP SUPPORT
RETAINING
SPRING
SLOT
FIG. 2
SOCKET HOUSING
FRAME
SOCKET HOUSING
ASSEMBLY
FIG. 3
FIG. 4
FIG. 5
SOCKET
HOUSING
ASSEMBLY
FRAME
MOUNTING
SUPPORT
MOUNTING
SUPPORT
SLOT
CLIP
KICK
REFLECTOR
RING
RETAINING SPRING
REMOVED
FIG. 1
JUNCTION BOX
MOUNTING FRAME
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:8021DW
A0399 Page 2 of 2
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
®
US & FOREIGN PAT. PENDING
7. POSITION KICK REFLECTORS
a.) After KICK REFLECTORS are properly assembled to
CLIPS, rotate RING to align KICK REFLECTORS
opposite walls to be illuminated.
For double wall washer see (Fig. 6).
For corner wall washer see (Fig. 7).
8. PUSH-IN
a.) For overlapping flange installation (Fig. 8), slip WHITE
TRIM RING over REFLECTOR. For Flangeless (Fig. 9)
and Self Flanged Trims, WHITE TRIM RING is not
required.
b.) Push REFLECTOR straight up to engage 3 RETAINING
SPRINGS.
For double wall washer see (Fig. 10).
For corner wall washer see (Fig. 11).
c.) Final adjustment can be achieved by rotating REFLEC-
TOR. NOTE: To remove REFLECTOR squeeze RETAIN-
ING SPRINGS to disengage top portion of reflector.
9. CARE AND MAINTENANCE OF ALZAK REFLECTOR
REFLECTOR surfaces can be cleaned by the following
methods:
a.) Wipe off with a soft, clean, dry, lint-free cloth.
b.) Wipe off with a soft clean cloth dampened in mild
detergent solution. Rinse, the wipe dry with lint-free
cloth or paper towel.
c.) Wipe off with a clean cloth dampened with a solution
of wetting agent and water (such as 2 oz. per gallon
“Pluronic L62-LF” by Wyandotte Products). Then wipe
dry.
WALL
KICK REFLECTOR
FIG. 6
WALL
KICK
REFLECTOR
FIG. 7
WALL
FIG. 8
WHITE TRIM
RING
FIG. 9
FIG. 10
FIG. 11
RETAINING
SPRINGS
REFLECTOR
RETAINING
SPRINGS
REFLECTOR
Loading...