Lightolier 7637AZ User Manual
I
/
INSTRUCTION SHEET NO
INSTRUCTIONS FOR AITACHING LYTESPOV
TO LYTESPAN” TRACK
IS:7637AZ
R0490
Page 1 of 2
FOR USE WITH LYTESPAN@ TRACK SYSTEMS ONLY.
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for reference.
LYTESPAN TRACK
Ar
INSTRUCTIONS FOR AITACHING
LYTESPOP TO SINGLE CIRCUIT TRACK
Align BEAD on L~ESPAN TRACK and
1.
GROOVE in FITTING before inserting into
LWESPAN TRACK. See Fig. 1. (If BEAD is NOT
aligned, a potential hazard may result.)
2.
Unscrew the TURN KNOB partially and position
LEVER. See Fig. 1.
To attach FITTING, squeeze BUITON and
3.
KNOB, insert into LWESPAN TRACK, and
release. Tighten TURN KNOB. This holds
FllTING to LYTESPAN TRACK mechanically. To
energize turn LEVER ail the way until LEVER is
parallel to LYTESPAN TRACK. See Fig. 2.
BEAD
GROOVE
FITTING
w’vTuRNKNoB
[
FIG.
1 J
I
To shift fixture location on the LYlESPAN
4.
TRACK loosen TURN KNOB slightly, release
LEVER and slide to new positon.
To remove fixture reverse the procedure in (3),
5.
BUTT
push TURN KNOB in and allow FllTING to
disengage.
Fixture can be left on LYTESPAN TRACK when
6.
not in use by turning LEVER to disconnect U
elect rically.
MOVABLE BRASS
INSTRUCTIONS FOR CONVERTING
CONTACT
LWESPOV Attachment FllTING ~
OPERATE ON 2 CIRCUIT TRACK
NOTE: To insure proper operation of fixture on
LOWER CIRCUIT, FIG. 3:
UPPER CIRCLflTj FIG. 4 and 5:
Two Circuit Lytespan Track, the BLACK
SPACER (provided) must be used at all
times on the plug assembly.
The BLACK SPACER is not used when
operating Lytespots on Single Circuit Track.
Illustrates contacts in low position with
spacer in place for lower circuit.
To convert attachment fitting for upper cir-
cuit, raise BRASS CONTACT to high position (as indicated by dotted line) by pulling
CONTACT as high as stop permits and slip
ping on BLACK SPACER as shown in Fig. 4
and 5.
BLACK
SPACER
~~%
I i
‘+’
—
\L
,+7”
,.
.
-.
FIG. 4
MOVABLE BRASS
CONTACT
FIG. 2 ~
IC ‘LACK SPACER
o
D
~
c
FIG. 3
STATIONARY SILVERED
CONTACT (COMMON)
PLUG
ASSEMBLY
,,.~..i ) .~~%
‘“’~””’’”,’%:’,’;g,-,
“=%$~,,,,,~h
I‘ . “Y
..
~~... ,’
\
7T
-.., ,/,,,,.;
FIG. 5
BLACK
SPACER
~’
INST’RUC’T’IONSFOR LAMPING DRAMALUX@ LOW VOLTAGE (SEE FIG. 6)
1. Loosen KNURLED KNOB on FIXTURE HOUSING and remove FIXTURE COVER.
2. Select voltage (12V or 5.5V depending on lamp being used) by setting Slide Switch by inserting
screwdriver or tool into slot in Slide Switch.
CAUTION: Do not use SLIDE SWITCH as ON/OFF SWITCH.
3. Install lamp by pushing into LAMP CONNECTOR until the rim of lamp snaps onto
LAMPHOLDER SPRINGS,
4. Slide FIXTURE COVER onto FIXTURE HOUSING and tighten KNURLED KNOB.
NOTE: For dimming control, use only variable autotransformer di’mmers or electronic dimmers
specifically designed for use with transformers such as Lutron NLV600 or SLV600P, Atmos LU-500 or
Hunt LV-5 or LV-6.
SLIDE SWITCH
FIXTURE HOUSING
. ~ “!P:N:’R
\
\
\
\
\
\
\
\
FIG. 6
FIXTURE COVER
Loading...