Lightolier 7226HRM User Manual

/
INSTRUCTION SHEET NO.
INSTALLATION OF PRE-WIRED QUAD TUBE POWERSPEC”
ELECTRONIC COMPACT FLUORESCENT REMODELER KITS
7218HT AND 7226HT SERIES (2 PIN QUAD TUBE) 7218HF AND 7226HF SERIES (4 PIN QUAD TUBE)
IS:7226HRM
READ AND UNDER~AND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these
Instructions for maintenance reference.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: WHEN USING ELECTRICAL EQUIPMENT BASIC SAFETY PRECAUTIONS MUST
ALWAYS BE OBSERVED INCLUDING THE FOLLOWING:
TO PREVENT ELECTRICAL SHOCK, TURN OFF ELECTRICITY AT ELECTRICAL PANEL
BEFORE PROCEEDING.
RISK OF ELECTRIC SHOCK. TO PREVENT ELECTRIC SHOCK, FOR PROPER OPERATION
AND SAFETY, THIS FIXTURE MUST BE GROUNDED.
THIS FIXTURE IS INTENDED FOR INSTALLATION IN ACCORDANCE WITH NATIONAL
ELECTRIC CODE AND LOCAL REGULATIONS.
TURN OFF POWER BEFORE I,AMPING AND RELAMPING.
- Do
not install fixture on a branch circuit having a Ground Fault Circuit Interrupter (GFCI). Typically
electronic ballasts may cause GFCI tripping.
WARNING—(RWK OF FIRE) DO NOT INSTALL INSULATIONWITHIN 3 INCHES OF FMTUF?ESIDES OR
WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HEAT
EXISTING CONSTRUCTION
=& p~@n
FIG.A
CUT OPENING
L
FIG. B
U. WIRE-IN
FIG. C FIG. D FIG. E
Ill. AllACH J-BOX
IV. AITACH V. SNARON
MOUNTING RING
FIG. F
VI. PUSH-UP
CUT OPENING (Fig. A)
Use MOUNTING RING provided as a template to cut a hole in the ceiling. Use inside diameter to scribe hole.
WIRE-IN (Fig. B)
.
Wire to supply leads. (For Cable, use built-in Cable Clamp in J-BoxJ White fixture lead to neutral supply lead. B!ack fixture lead to hot (120V)supply lead. Bare fixture wire to supply ground. Use wirenuts (local hardware item). Place all electrical connections in the J-BOX. Attach J-BOX COVER onto J-BOX.
1.ATTACH J-BOX (Fig. C & G)
Attach J-BOX PIJ4TEto ceiling by pushing NAIL
1.
TAB on J-BOX PIATE into ceiling, Fig. G.
2. Push LONG LEG of NAIL CLIPS (supplied in parts bag) into RAISED BUMP of J-BOX PIATE
and SHORT LEG into ceiling, Fig. G.
3. Make sure that the J-BOX PLATE is securely
attached to the ceiling and the J-BOX is in the position shown in Fig. G.
NA
LO
OPENING IN CEILING
FIG. G
RING
J-BOX
1- I
<*HTC> LBE 1?”;?t;Z;f;,N2;;;l;,EZ;;Y
INSTALLATION OF PRE-WIRED QUAD TUBE POWERSPEC”
ELECTRONIC COMPACT FLUORESCENT REMODELER
7218HT
7218HF
A7TACH MOUNTING RING
Iv.
Insert MOUNTING RING into CEILING as shown (Fig. H).
1. In order to install SIDE MOUNTED type REFLECTORTRIMS when the ceiling thickness is greater than 1‘<the additional ceiling material opposite the JUNCTION BOX must be removed (Fig. K.)
2. Inseri REFLECTOR TRIM, SOCKET CUP first
into ceiling opening where the material was removed opposite the JUN~lON BOX. Pivot the REFLECTORTRIM and push it up into the
ceiling (Fig. K.)
AND 7226HF SERIES (4 PINQUAD TUBE)(CONTINUED)
CLIP ASSEMBLY (Fig. 0
1.
Insert CLIP from inside housing, through ‘T slot.
2. Apply downward force with screwdriver on top of CLIP or engage screwdriver in slot in CLIPS flange.
3. Apply force until CLIP is
CLIP REMOVAL (Fig. J)
3.
Insert a small blade, short-handled screwdriver through the CLIPSS screwdriver slot, and press against the opposite side of the CLIF?
2. Push CLIP up to top of “T” SLUT and remove.
V. SNAFON (Fig. E)
VI. PUSH-UP (Fig. F)
CEIL
I
f
AND 7226HT SERIES (2 PIN QUAD TUBE)
snugly seated.
SEE SEPARATE REFLECIUR TRIM INSTRUCTION
1
SHEETS.
JUNCTION BOX
/r
I
—7
“=- REFLECTOR
TRIM
.-1
2“ MAX.
CEILING \
4/%
/f ‘i\
1!
KITS
\
TO REMOVE
FIG. H
TO INSERT
f+
‘1
‘T”
SLOT
I
---­1+
)..’. : ,;. .
Y
‘d CEILING
FIG. I
—.——
A
IS:7226HRM RI 293
Page2 of 2
SLOT
RING
1;::;:;
STEP 1
SHORT HANDLE
SCREWDRIVER
STEP 2
STEP 3
I
\\
REMOVAL
FIG. J
/
WIRHIJGDIAGRAM FOR 2 PIN BASE LAMP
I
T
L I
r—
1 ~
L- —
I
NEUTflAL (wH!TQ
N
P
I&n
u
T
I
BALLASTCASE MUST BE GROUNDED
FIG. K
BLACK
WHITE
WHITE
— w ~ucx
LAMPS
WIRING DIAGRAM FOR 4 PIN BASE LAMP
RED
I
>
-1
[
,E.TRAL..+~-
N
CMKTE1
P
HOT
(BL4CKI
u T
+.L
!+
L—. + —
BALLAST CASE MUST BE GROUNDED
RE9
W2Low
vELLm
BLUE
e4uE
Zr
I
YELLOW YEUBLK
YE”BLK
YELLOW
c~
o
LAMPS
WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGNTOLIER INC. USE OF OTNER MANUFA~RERS’
REFLECTOR TRIMS VOIDS TNE UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE
Loading...