Lightolier 6273 User Manual
READAND UNDERSTANDTHESEINSTRUCTIONS BEFOREINSTALLINGFIXTURE
“hisfixture is intended for installation in accordance with the National Electrical Code and local regulations.
“oassure full compliance with local codes and regulations, check with your local electrical inspector before
mtallation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:6273
1094
Page 1 of2
Y
b
INSTRUCTIONS FOR ATTACHING SOF-TECH” LOW VOLTAGE TO LYTESPAN” TRACK
FOR USE WITH LYTESPANiTRACK SYSTEMS ONLY
INSTRUCTIONS FOR ATTACHING SOF-TECH” LOW VOLTAGE TO SINGLE CIRCUIT TRACK SYSTEM
1. Insert into LYTESPAN TRACK (see Fig. 1). LOCKING I-EVER must be in same side of track as BEAD.
2. Rotate FllllNG 90” clockwise (see Fig. 2).
3. Rotate FITTING until LOCKING LEVER snaps and locks in place (see Fig. 3).
4. To remove: depress LOCKING LEVER, then rotate FITTING 90” counterclockwise.
~=_=&;_Q/-’’’’’’~~TRACK
~}1 Fi
Ii-. —_—_–:=.4–,’:,
~;~p,,
\, ,:\yil .;. -~
“ i---:- ‘“-
-+
1-””
LOCKING
LEVER
r
BEAD
45 == d
1
‘-%2
—
—
.,
~
~ 1.,
REMOVE
\,,,—-.
.-’
J
TO
FIG.1
INSTRUCTIONS
ATTACHMENT FITTING TO OPERATE ON 2 CIRCUIT TRACK
(See Fig. 4) BRASS CONTACT can be raised or lowered. Broken line indicates position
for 1 circuit track system or lower circuit of 2 circuit track system.
To convert attachment FITTING for upper circuit of. 2 circuit track, raised BRASS
CONTACT to high position by lifting CONTACT as high as stop permits and CONTACT
clicks into place.
SEE BACK FOR LAMPING
FOR CONVERTING SOF-TECH@ LOW VOLTAGE
FIG.2
[!
.,,
FIG.3
BRASS CONTACT
./
>
q-
*L
(~’, &:.;=s
G-
[1
w—-
4
FIG.
FALL RIVER, MASSACHUSETTS, 02720
@
,,=LOCKING
LEVER
M c> H Tcx
1E 1? MONTREAL,QUEBECCANADA
d
I
INSTRUCTION SHEET NO.
1S:6273
----- _..
1094
1.
2.
3.
4.
Page z orz
Check to see that power is OFF when Iamping or relamping.
For 6273B insert the two I-AMP PINS into the SOCKET HOLES (Fig. 5a);
For 6273T insert the two LAMP STUDS into the SOCKET HOLES and
twist clockwise (Fig. 5b).
Insert COVER with LAMP into RING until (3) LAMP SPRINGS engage
fully with the RING (Fig. 6).
To aim fixture, rotate as shown (Fig. 7)
ADJUSTING SOF-TECH@ LOW VOLTAGE
INSTRUCTIONS FOR LAMPING AND
(- ‘-’)
SOCKETHOLES
RING
LAMP GLASSSHIELD
(WITH 6273B ONLY)
—
,.
@
C-Eg$il
“1“y
—
k
L..
(cc
t“q-
. ..[+]-
A. ..g
...—.
———
~T: =>.
/<
‘“
,/
6
&..__&[.-
~ ..__ .__-:/’
\:__
- -...,
.<__ /. -
——
FIG.6
-.
1 .:=-—
—
LAMP SPRING
1 .-—
r
FIG.5a
(6273b)
180”
VERTICAL
ROTATION
FIG.5b
(6273T)
v“
0“
FIG.7
HORIZONTAL
ROTATION
180”
d
Loading...