Lightolier 6196 User Manual

v

E~~~~f~;,N~~

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
ThisfixtureisintendedforinstallationinaccordancewiththeNationalElectricalCodeandlocalregulations.
Toassure

installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

full compliance with local codes and regulations, checkwith your local electrical inspector before

Retain these instructionsfor maintenance reference.

INSTRUCTIONS FOR ATTACHING COIL CORD CLAMP-ON MONOPOINT

FORUSE WITH LIGHTOLIER TRACK FIXTURES ONLY

INSTRUCTION SHEET NO.

IS:6196

A1294

Page 1 of2

ATTACHING COILEDCORDCLAMP-ON MONOPOINT

TO PIPE

This CLAMP is designed to mount on round pipe, pipe structures,
or round supports. Secure the CLAMP to structure by tightening

the TIGHTENING KNOB and the body allowed to face downward

to minimize

prong 120V, 60 Hz, grounded receptacle is required to energize
the unit,

ORPIPESTRUCTURE

force required to support I_ytespots (Fig. 1). A (3)

AllACHING LYTESPOTWITH “T’ ADAPTORTO COIL
CORDCLAMP

1.Position LEVER as shown in Fig. 2,

2. Align BEAD on MONOPOINT ADAPTOR with GROOVE in “T”
adaptor, see Fig. 2 (If BEAD is NOT aligned, a potential hazard
may result). Rotate LEVER 90 degrees to secure Lytespot.

3. To remove !_ytespot: Hold fixture and rotate LEVER 90 degrees
(Fig. 3).

CAUTION- INJURY TO PERSONS AND DAMAGE TO

THE LAMP AND/OR MOUNTING SURFACE MAY RESULT
IF THE LAMP IS PULLED FROM THE SURFACE. TO
REDUCE THE LIKELIHOOD OF SUCH INJURY OR
DAMAGE, MOUNT ONLY ON A SURFACE THAT IS
MECHANICALLY SOUND.

TIGHTENING KNOB

PIPE OUTSlOE

DIAMETER 5/8” TO 2“
RECOMMENCED

CLAMP

MONOPOINT

AOAPTOR

FIG. 1

co

GAS

2

FIG.

,,

‘T” ADAPTOR(lDIA. SHAIT)
JSEDWITHCAT.NO.S6435&

u

1-I

7599

z

Not designed to work with

NOTE:

COIL CORD CLAMP-ON MONOPOINT

FIG. 4

C3H TC> L IE R“

BOXADAPTOR

E

FIG. 3

GROUNO

INSTRUCTIONSHEETNO.

1S:6196

A1294
INSTRUCTIONS FOR ATTACHING LYTESPOT WITH SQUAT ADAPTOR TO COIL CORD CLAMP

1, Insertthe SQUATADAPTERinto the MONOPOINTADAPTOR.The LOCKING LEVER must be on the same side as the BEAD located on the

MONOPOINT ADAPTOR (See Fig. 5). Rotate the SQUAT ADAPTOR 90 degrees clockwise until LOCKING LEVER locks into place (See Fig. 5,
6 & 7).

2. To remove, depress LOCKING LEVER and rotate SQUAT ADAPTOR 90 degrees counterclockwise.

I CAUTION- SUPPORT THE MONOPOINT ADAPTOR WHENEVER MANIPULATING THE FIXTURE. I

BEAD

Page 2 of 2

MONOPOINT
ADAPTOR

INSTRUCTIONS FOR AITACHING COIL CORD CLAMP-ON

MONOPOINT

FORUSEWITH LIGHTOLIERTRACKFIXTURESONLY

(Cent’d)

*

LOCKING
LEVER

*

L

FIG.5

INSTRUCTIONS FORAllACHING LOW VOLTAGE TO COIL CORD CLAMP

1.Insert the LOW VOLTAGE ADAPTOR into the MONOPOINT ADAPTOR. The LOCKING LEVER must be on the same side as

on the MONOPOINT ADAPTOR (See Fig. 8). Rotate the LOW VOLTAGE ADAPTOR 90 degrees clockwise to secure fixture
electrical connection (See Fig. 8,9 & 10).

2, To remove, rotate LOW VOLTAGE ADAPTOR 90 degrees counterclockwise.

I CAUTION- SUPPORT THE MONOPOINT ADAPTOR WHENEVER MANIPULATING THE FIXTURE. I

w

RFAD —

SQUAT
ADAPTOR

1

MONOPOINT

ADAPTOR

‘

&

FIG.6

FIG.7

%

the BEAD located
and make

LOCKING ~

“-”--::AGE

LEVER

FIG.8

/

ADAPTOR

FIG.9

—

FIG. 10