Lightolier 26050 User Manual
READ AND UNDERSTAND ALL TRACK, CONNECTOR, FEED-IN-KITS, AND ACCESSORY
INSTRUCTION SHEETS BEFORE INSTALLING ANY PROSPEC™ TRACK ITEM.
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal
code specifications. To assure full compliance with codes and regulations, check with your local electrical
inspector before installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:26050
A0197 Page 1 of 2
Installation Instructions for ProSpec™, In-Line, "L", "T", and "X" Connectors / Circuit Diagrams
™
For use with ProSpec
Caution:
• Turn off power at fuse box before installing track.
• Instructions for grounding Feed-in Kit must be followed.
Failure to do so may result in a hazardous condition.
• Use only #12 ga. solid copper wire in connectors to
maintain proper track rating.
• Observe polarity, white (neutral) wire must be connected
to terminal marked "NEUT". Failure to observe Polarity may
result in an electrical hazard.
• Do not use Track as a conduit support. Independent conduit
supports (such as suitable conduit straps) must be used to
attach the conduit installation to the building structure.
INSTALLING CONNECTOR INTO TRACK SECTION
1. Remove Dead-End Cover if necessary by pulling it out of track
(save Dead-End Cover).
2. Push Connector into the track until there is no gap between the
track unit and connector. Ensure that the contact blades are
aligned with the copper wires in the track during assembly.
3. Tighten the locking screw(s).
Track System Only.
Track Unit
Connector
Bottom Cover
Fig. 1
Dead End
Connector
Locking Screw
Track Unit
POWER FEED TO THE CONNECTOR(S)
DIRECT POWER FEED
1. Remove the bottom cover (if required) by snapping it out of the
connector (save cover).
2. Remove K.O. plate from the connector.
3. Remove the K.O..
4. Attach the electrical connector onto the K.O. plate using the nut
provided. Align the electrical connector such that the connector is
hidden by the track width.
5. Attach the K.O. plate onto the connector using the screw that was
previously removed.
6. Pass cable or conduit through electrical connector and clamp cable
or conduit to electrical connector.
7. Form the wires to the appropriate screw terminals, cut and strip
wires and attach to the screw terminals (see wiring section of
instruction sheet).
8. Snap the bottom cover onto the connector.
There are additional feed in kits (Floating Canopy, End Feed Canopy,
Floating Invisible Feed, Grid Ceiling Canopy Kit, Stem Kits....) that can
be used with these connectors. See the Instruction Sheet supplied
with the Feed-in Kit for detailed instructions on mounting the kit to
the connector.
Fig. 2
Electrical Connector
Fig. 3
(by Others)
K.O. Plate
Nut
Knock Out
Bottom Cover
Track Unit
Dead End
Track Unit
FALL RIVER, MASSACHUSETTS 02720
MONTREAL, QUEBEC, CANADA
© 1997
INSTRUCTION SHEET NO.
IS:26050
A0197 Page 2 of 2
Installation Instructions for ProSpec™, In-Line, "L", "T", and "X"
Connectors / Circuit Diagrams
For use with ProSpec
™
Track System Only.
WIRING THE CONNECTOR(S)
Use 12 ga. solid copper wire when feeding the connector(s). Each
circuit is rated for 120V, 60Hz, 20 AMPs.
NOTE: The "L", "T", "X", and In-Line Connector allow for multiple
circuits to be introduced into them. The Connectors are not polarized
and can be installed into the track in any orientation. Therefore,
identification of the circuits during wiring needs to be controlled by
the installer or electrician. The brass screw terminals are for the hot
leads. The silver screw terminals are for the neutral leads, and the
terminals marked "GND" are for the ground. The individual circuit(s)
are arranged vertically. (See diagrams). The "L" and In-Line
Connectors are pre-wired. These wires may be removed if the wiring
needs to be different. Loosen the screw terminals and remove the
wires.
1. Form the wires to the screw terminals, strip the insulation
back 1/2".
2. Slip the wire under the terminal screw head. Tighten all screw
terminals when wiring is completed.
3. Snap bottom cover onto the connector to cover the wires.
Circuit 2
FIG. 4
Use 12 ga. solid copper wire for
feed connections including
Circuit 1
N
Power
Terminals
N
Neutral
Terminals
ground.
Ground Terminal
Circuit 1
Circuit 2
.50
Two wires may be
attached to one
screw terminal.
"X" CONNECTOR
Typical Circuit
Identification
Neutral Terminal
Circuit
GND Ground
GND
GND
Cir-1
Cir-1
N-2Cir-2
N-1
N-2Cir-2
N-1
GND
Cir-1
N-2Cir-2
N-1
GND
Cir-1
"T" CONNECTORIN-LINE
N-2Cir-2
N-1
"L" CONNECTOR
© 1997
Loading...