Lightolier 2000AICV User Manual

Lytecaster

®

Recessed Downlighting 2000AICV

Page 1 of 1 3 3/4" Aperture Low Voltage MR16 Insulated Ceiling AirSeal® Frame-In Kit

Frame-in Kit

Reflector Trim

Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.

Frame-In Kit Reflector Trims — See Individual Reflector Trim Specification Sheets

Open Downlight Enclosed

Aperture Cone Satin Cone Baffles Slot Pinhole Diffuser

2000AICV 2012 2008 2005 2006 2011 2090LV
2012NM 2008NM 2005WH
2013BKNM 2010 2005BNM
2013CD 2010NM 2005NM
2013CDNM
2013NM
2013BK
2013WH
2013
2013WD
2013WDP

Features

1. Housing: .026” galvanized steel. UL listed for direct contact with thermal

insulation. AirSeal® housing minimizes air leakage to less than 2 CFM at 1.57
PSF, which complies with Washington State Model Energy Code (Section

602.3.3) and reduces heat loss and condensation in ceiling. Access door for
inspection of junction box.

2. Mounting Frame: .036” (#20 ga.) galvanized steel. Accommodates ceilings
up to 1” thick. Four slots are positioned 90° apart to simplify alignment. Push­in/twist-out rotoclips hold reflector flush to ceiling.

3. Junction Box: 2”X 4” X 4”;.063” (#16 ga.), galvanized steel. UL listed for
maximum of 6 No. 12 ga., 90° C through branch circuit conductors. Quick
release “L” shaped cover for outside access to wiring. Access door inside of
housing allows easy inspection of wiring without removal of housing. Integral
cable clamps permit attachment of nonmetallic Romex® or armored cable
without the need for additional connectors.

4. Mounting Bars: .059 (#16 ga.) galvanized steel. 13” long bars extend to 27”,
rotatable and lockable, with integral T-bar tabs. Attach to wood joist or T-bar
ceiling without need for accessories.

5. Socket Housing: Aluminum, with lamp adjustment assembly allows 35°
max. vertical, 358° horizontal adjustment.

6. Socket: Field replaceable. Two pin socket, pre-wired with #18 SF1 leads to
junction box.

7. Thermal Protector: Mounted inside housing. Meets NEC and
UL requirements.

8. Transformer: Mounted inside housing, magnetic. 120V pri-mary, nominal 12V
secondary. Removable from below.

Dimming

Dimming Controls: use only dimmers specifically designed for use with magnetic
transformers, like Lightolier Onset® Sunrise® series LV or VA, dimmers, or any
Lightolier Controls dimming systems. Low voltage fixtures may produce audible
sound when used with dimmers, which may be objectionable in acoustically criti-

cal areas.

Options and Accessories

Mounting Bars: 1976 - 13” set of (4)
Replacement Kit:
Plaster Ceiling Ring: 1959 - 7/8” depth for wet plaster ceilings.
MR 16 Socket Replacement: 1975B

Labels

UL (Type I.C., Suitable for Damp Location), I.B.E.W.

Complies with Washington State Air Leakage Requirements as stated in the
Model Energy Code and the Washington State Energy Code.

Romex® is a registered trademark of General Cable Industries Inc.
US Patent No’s: 5,045,985

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):
Notes:

631 Airport Road, Fall River, MA 02720 • [phone] • Fax [phone]

We reserve the right to change details of design, materials and finish.

www.lightolier.com © 2008 Philips Group • I1208

Lightolier is a Philips group brand