Lightolier 1101FDIC User Manual

Performance Recessed CFL Downlighting 1101FDIC

1

2

3

4

5

6

7

Reflector Trim

Frame-in Kit

Page 1 of 1 6 ¾" Aperture, 1 Light, Compact Fluorescent, IC AirSeal®, Frame-In Kit

Overall Length

16 3/8"

12 1/4"

13 Min.

24" Max.

Height: 7 1/4"

Ceiling Opening: 6 15/16"

Complete Fixture consists of Frame-In Kit and Reflector Trim. Select each separately.

™

Uniframe™
Frame-In Kit

1101F DICMX1**

(Advance Mark 10- 120V)

1101F DICMX2 **

(Advance Mark 10- 277V)

26w Quad/Triple
GX24q-3 Base
120v – 0.26amp max
277v – 0.11amp max

32w Triple
GX24q-3 Base
120v – 0.32amp max
277v – 0.14amp max

42w Triple
GX24q-4 Base
120v – 0.41amp max
277v – 0.18amp max

Uniframe

Horizontal
Open

1101HCL
1101HCD
1101H WH

Universal Series Reflector Trims (Reference Trim Spec Sheet for Recommended Lamping)

Cone Satin Cone Bafe Wall Wash Wet Location Cross Blade

1112 * 1145
1113* 1146 / 1146CD
1113BK* 1143
1113WH 1144 / 1144CD
1113 CD *

Compact Fluorescent Performance Series Reflector Trims

Horizontal Wall

Wash - Single

1101HCLSW
1101HCDS W
1101H WHSW

Horizontal Wet Location
Lensed / Diffused

Clear Lens Fresnel

1101HCLC 1101HCLF
1101HCDC 1101HCDF
1101H WHC 1101H WHF

Opal Lens

1101HCLO
1101HCDO
1101H WHO

110 8*

1110 *

110 5*
110 5B N M
110 5W H

117 6
117 6W H

Overall Width

10 3/8"

Top View

Horizontal

Cross Blade

1101HACB
1101H WHCB

119 5
119 6
119 6C D

112 1

1124
113 4
1177SH
117 8S H
119 0

*Add NM sufx to catalog number
for Natural Metal ange and nish.**Add N to catalog number for preset nails.

113 2

Features

1. Housing: .028" (#21ga.) aluminum. UL listed for direct contact with thermal

insulation. AirSeal® housing minimizes air leakage to less than 2 CFM at 1.57
PSF (or 75pa), which complies with Model Energy Code (Section 602.3.3) and
Washington State Energy Code (Section 502.4) and reduces heat loss and
condensation in ceiling. Access door for inspection of junction box.

2. Mounting Frame: .032 (#22 ga.) galvanized steel. Accommodates ceilings
up to 1 1/2" thick. 3/8" deep integral lip. Locks into position along length
of mounting bars with locking screw and bendable slot. Four slots are
positioned 90° apart to simplif y alignment. Push-in/twist-out roto-clips hold
reflector flush to ceiling.

3. Junction Box: 2" X 4" X 3 1/2" (22 cu. in) .032" (#22 ga.) galvanized steel. UL
listed for maximum of 8 (#12 ga.) 90°C through branch circuit conductors.

4. Mounting Bars: .059" (#16 ga.) galvanized steel. Bars pivot for easy
attachment and wire-in below ceiling line. Bars extend to accommodate 16"
to 24" O.C. joist spacing. Bars can accommodate 12" O.C joist spacing after
a slight field modification (see Instruction Sheet). Features integral self
tapping phillips screws for secure attachment to wood or metal construction.
Attaches to T-bar ceilings without the need of accessories.

5. Ballast: Mounted inside housing. 120V or 277V UL Listed Electronic Dimming
Ballast, end of lamp life protection, class “P” thermally protected, class “A”
sound rating.

6. Socket: Four-pin base, molded thermoplastic socket, prewired with No. 18
AWM leads to ballast.

7. Socket Housing: .036" (#20ga.) Galvanized Steel housing attaches to
reflector trim by spring clip for precise optic alignment.

Lightolier is a Philips group brand

Options & Accessories

Extra-Thick Ceiling
Mounting Ring: 1967B - 1 1/4" to 2" thick ceilings

Labels

cULus Listed (Type I.C., Suitable for Damp Location), I.B.E.W.

Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.

®

is a registered trademark of Lightolier

AirSeal

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:

631 Airport Road, Fall River, MA 02720 • [phone] • Fax [phone]

We reserve the right to change details of design, materials and finish.

www.lightolier.com © 2008 Philips Group • C0608