Lightolier 1100F User Manual
®
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
LOCKING SCREW
LINE UP BOTTOM
EDGE WITH BOTTOM
OF WOOD JOIST
MOUNTING FRAME
CENTERING SLOTS
ADJUSTABLE
MOUNTING BARS
T-BAR
1" MAX
1-1/2" MAX.
G1 G2
Fig. G
Fig. E
ADJUSTABLE MOUNTING BARS
MOUNTING FRAME
(NARROW SIDE)
LINE UP BOTTOM EDGE WITH
BOTTOM OF WOOD JOIST
Fig. F
ADJUSTABLE MOUNTING BARS
Fig. A
1. Frame-In
Fig. B
2. Close-in
Fig. C
3. Snap-On
Fig. D
4. Push-Up
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal
code specifications. To assure full compliance with codes and regulations, check with your local electrical
inspector before installation. T o prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
Installation of Lytecaster®Frame-in-Kit 1100F Series
INSTRUCTION SHEET NO.
IS:1100F
D0605 Page 1of 2
NEW CONSTRUCTION
1. FRAME-IN (FIG. A)
NOTE: ADJUSTABLE MOUNTING BARS are pre-assembled on long side of
2. CLOSE-IN (FIG. B)
NOTE: For wet plaster ceiling, use Plaster Ring Accessory No. 1961 - order
3. SNAP-ON (FIG. C) See separate instruction sheet
4. PUSH-UP (FIG. D) for your choice of reflector trim.
WARNING – (RISK OF FIRE)
Do not install insulation within 3 inches of fixture sides or wiring
compartments, nor above fixture in such a manner as to entrap heat.
WOOD JOIST/METALSTUD CONSTRUCTION (FIG. E): Line up bottom edge of ADJUSTABLE MOUNTING BARwith bottom of wood joist.
Fasten MOUNTING FRAME to
TABor nail into joist.
SUSPENDED GRID CEILING (FIG. G):
Position notched area of ADJUSTABLE MOUNTING BARSon top of TBAR for proper spacing to finished ceiling. Lock MOUNTING BARS by
bending TABunderneath T-BAR BEAD(Fig. G1). For round T-BAR BEAD,
use screws to lock MOUNTING BARS (Fig. G2).
WIRE TO SUPPLY LEADS:
For cable, use built-in cable clamp in J-Box. Connect white fixture
leads to neutral (white) supply leads. Black fixture leads to hot (black)
supply leads. Bare fixture wire to supply ground. Use wirenuts (local
hardware item). Place all electrical connections in the J-Box, attach JBox cover.
MOUNTING FRAME for rigidity and ease of installation (Fig. E).
MOUNTING BARS must be removed and installed on narrow side of
MOUNTING FRAME if installing in 16” joist spacing (Fig. F).
MOUNTING BARS can be extended to 24”. The MOUNTING FRAME
can be mounted off-center.
For suspended ceilings, make certain that bottom of MOUNTING
FRAME is no higher than 1” above finished ceiling (Fig. G).
Install plasterboard or other dry type ceiling. Hole in board can be cut
either on floor or after the board is secured in the ceiling. Use MOUNTING FRAME opening as cutting guide template for hole – make sure
ROTO CLIPS are rotated out of hole area.
separately.
wood joist by nailing MOUNTING BAR
U.S. Patent Nos. 5,045,985; 4,313,154; 4,327,403
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
INSTRUCTION SHEET NO.
®
MOUNTING FRAME
BRIDGE
SLOT
Fig. H
ROTO CLIP
STAPLE
MOUNTING FRAME
CEILING MATERIAL
Fig. I
FRAME
J-BOX COVER
J-BOX
J-BOX SPRING
J-BOX COVER
Fig. J
IS:1100F
D0605 PAGE 2OF 2
EXISTING CONSTRUCTION
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code and local or Federal
code specifications. To assure full compliance with codes and regulations, check with your local electrical
inspector before installation. T o prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
Fig. A
1. Cut-Opening
Fig. B
2. Wire-in
Fig. C
3. Put Through
1. CUT OPENING (FIG. A AND FIG H)
a. Remove ADJUSTABLE MOUNTING BARS.
b. Use MOUNTING FRAME opening as template.
c. Break off BRIDGE on MOUNTING FRAME as shown in
Fig. H by breaking WEBS on SLOTS with cutting plier.
2. WIRE-IN (FIG. B)
For cable, use built in Cable Clamp in J-BOX. Connect white fixture
lead to neutral (white) supply lead. Black fixture leads to hot (black)
supply lead. Bare copper and/or green insulated wire(s) must all be
connected to supply ground. Use wire nuts (local hardware items).
Place all electrical connections in the
J-BOX. Attach J-BOX COVER onto J-BOX.
3. PUT THROUGH (FIG. C AND FIG. J)
Detach BALLAST ASSEMBLYfrom J-BOX and pass MOUNTING
FRAME into ceiling as shown in Fig. C. Reattach BALLAST ASSEMBLY.
4. ANCHOR (FIG. D AND FIG. I)
Using STAPLE (order separately Cat. #1985S), slide long end underneath raised embossing and short leg into ceiling (Fig. I).
5. SNAP-ON (FIG. E) See separate instruction sheet
6. PUSH-UP (FIG. F) for your choice of reflector trim.
BALLAST REPLACEMENT (FIG. J)
NOTE: Ballast replacement must be provided by a “qualified electrician”.
1. TURN OFF POWER.
2. Remove reflector trim from FRAME-IN KIT.
3. Remove J-BOX COVER nearest ceiling opening by lifting SPRING.
4. Disconnect all input wiring to ballast.
5. Remove BALLAST ASSEMBLYfrom J-BOX by pulling SPRINGupward
(Fig. J).
6. Remove BALLAST ASSEMBLYthrough ceiling opening.
7. Release all wires from BALLAST WIRE CONNECTORS by inserting small
blade tool, with insulated handle, into WIRE RELEASE SLOTS. (Fig K).
NOTE: Replacement ballast kits generally are supplied with this special
wire release tool.
8. Remove (2) NUTS which hold BALLAST to J-BOX COVER.
9. Replace old BALLAST with new BALLAST and attach with NUTS
to J-BOX COVER.
10.Reassemble new BALLAST ASSEMBLY to J-BOXby snapping
onto J-BOX spring (Fig. J).
11.Rewire fixture. See WIRINGDIAGRAM on BALLAST LABEL.
Fig. D
4. Anchor
REMOVE
Fig. E
5. Snap-on
INSERT
Fig. F
6. Push-up
WIRE RELEASE
BLADE
(BY OTHERS)
WIRE RELEASE
SLOTS
BALLAST WIRE
CONNECTORS
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
Loading...