Lightolier 1094 User Manual

READ AND UNDERSTAND T“HESE INSTRUCTIONS BEFOf+E INSTALLING FIXTURE

This fixture is intended forinskdlation in accordance with the National
regulations.To assure full complian= with local maes and regulations, check witt your iocai elee~icai

inspector before installation. To prevent eleckk=al shack, turnoff electriaty at fuse box before proceeding.

.,’

I

I
I

Retain these instructions

INSTRUCTIONS FOR lNSTAtLATION

for maintenance reference.

Electrical Code and Iocaf

., .,. ,.,

A.”:”~o~’ (j&~Go~fi: ‘oTJiLET BOX MOUNTING.

1...Loosen and remove BATTERY NUT that secures MOUNTING PLATE” to

. .

.,

..!:’,

.FIXT~E BODY. Remove MOUNTING PLATE from;> FIXTURE BODY.

.:?.

Screw COVER PLATE to the backside, of MOUNTING PLATE with SCREWS
provided.

~’3. Pull supply wires from OUTLET BOX through WIREWAY HOLE in

MOUNTING PLATE.

“,,’4.’Using outlet box screws (provided’ with outlet box) secure

“MOUNTING PLATE to outlet box using appropriate slots in MOUNT-

%.

n;:&

ING PLATE.

,.

B::FOR VERTICALLY MOUNTED RECTANGULAR GEk OR SWITCH BOXES.

1. Loosen and remove BATTERY NUT that secures MOUNTING PLATE to
FIXTURE BODY. Remove MOUNTING PLATE from FIXTURE BODY.

i

Pull supply wires from outlet box through the WIREWAY HOLE in
MOUNTING PLATE.
Using OUTLET BOX SCREWS: (provided with outlet box) secure the

2.

MOUNTING PLATE to OUTLET BOXusing the two horizontal slots.

INSTRUCTION SHEET NO.

IS:4910

,. ..2. . .-. ? ..=

, -1094+AGE-I–”OF: --2

...- -

,.

5

I

I

I

c. INSTALLATION OF FIXTURE BODY.

While supporting fixture, make Connections.

1.
or fixture lead without tracer marks to black (ho:) supply lead

.,

white fixture lead or fixture lead with tracer marks to white

(neutral) supply lead.

wires and all must be connected to grounding terminal or wire

in outlet box.

OL’TLEEBOXq

\

\

a

Use wirenuts (local hardware item) .

HORIZONTAL

I_

P

-% > II

!40UNTING

COVER

Black fixture lead

Uninsulated fixture wires are ground

,“

\

.“

THREADED

BALLS

THREADED

STUDS

GLASS

SLOT

“.

\

-BATTERY

NUT

SLOT

/

):

1.

“O

/’

.“

?!!!!!! -

.“

::’ZR;;5--I

EECTANGUMR SLOTS

HOUSINGTAB

WIRE NUT

FIXTUREBODY

..

/

READ AND UNDERSTAND THESE iNSKiUCTIONS BEFORE INSTALLING FIXTURE

~~1~ fi~re i5 jntended for installation in

~eoula~ons.To assure full campliancevfi!! local

inspector

beroreinstallation. To preventelecbical shock,turnoff,electriaty atfuseboxbeiore proceeding.

Retain these instructions for maintenance reference.

NOTE :

For supply connections use wire rated for “at least 75° C.

amrdancz with tie National Eiectrirzl Code and 10d

males and regulations, Cheti with you; Iod elecrrd

——.,, ———...—... .- .—-—.

.-

. . .. ..

INSTRUCTION SHEET NO.

“[s:a9 ,10

“--1094 PAGE”2 “OF 21:

,. -.. .

.

__.._: -——-J

\

WARNING-RISK OF FIRE.. Most dwellings built before 1985 have supply
wire rated 60° C.

installation.

;’.7.

~consult”.a,.qualified electrician before

CAUTIO.~: Push SUPPIY wires.and wir”enut c~nriections back into j-box

:?

2. Mount FIXTURE BODY to MOUNTING PLATE by aligning HOUSING TABS
up ,,through RECTANGULAR SLOTS in MOUNTIN~ PLATE.

CAUTION: Make certain that no wires are pinched between mounting

plat,e and fixture body.
Gen$ly push fixture body against wall until MOUNTING STUD comes

.3.

I

I

thcough SLOT in FIXTURE BODY.

Install recommended lamp.

4.

CAUTION: Maximum wattage marked on fixture must not be exceeded.

Install GLASS

5.

glass facing down,

over two THEADED STUDS WITH etched pattern on

tighten two THREADED BALLS onto THREADED

Secure in place using battery nut

STUDS to secure glass. Do not overtighten!’

Note: glass should be

sure on front portion

removed for cleaning as undue downward pres­could cause glass support bracket to bend.

-.

,..,

..:,

.. ­;

-...’

,,

. . . . .-_— ... - .-

.-

-L-.

.

I

1

!
I

1

---

I

.—.—. .—-. .

. . . .

—