Lightolier 1004ICV User Manual
Lytecaster
®
Recessed Downlighting 1004ICV
Page 1 of 1 5” Aperture 0® Low Voltage AirSeal® Insulated Ceiling Frame-In Kit
1004ICVN
(Integral Nail)
8
7
1
2
5
5” Aperture: Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.
6
1004ICV
(Integral Screw)
3
4
13 3/4” MIN.
24” MAX.
Overall Length
1004ICV:
15 5/16”
12 1/4”
Overall Width
1004ICV: 10 3/8”
Height: 7 1/4”
Ceiling Opening: 5 1/4”
Top View
Frame-In Kit Reflector Trims — See Individual Reflector Trim Specification Sheets
Adjustable
Baffles Aperture Cone Pinhole Elbow
1004ICV 1055LV 1056LV 1064WDLV 1052LV 1062LV
1004ICVN 1055WHLV 1063LV 1064WDPLV
1064LV
1064CDLV
Frame-In Kit
Reflector Trim
Features
1. Housing: .032” (#20 ga.) aluminum. UL listed for direct contact with thermal
insulation. AirSeal® housing minimizes air leak-age to less than 2 CFM at
1.57 PSF (or 75pa), which complies with Model Energy Code (Section 602.3.3)
and Washington State Energy Code (Section 502.4) and reduces heat loss and
condensation in ceiling. Access door for inspection of junction box.
2. Mounting Frame: .032 (#20 ga.) aluminum. Accommodates ceilings up to 1”
thick. 3/8” deep integral lip. Locks into position along length of mounting bars
with locking screws and bendable slot. Four slots are positioned 90° apart to
simplify alignment. Push-in/twist-out roto-clips hold reflector flush to ceiling.
3. Junction Box: 2” X 4” X 3 1/2” (22 cu. in.) .032” (#22 ga.) galvanized steel.
U.L. listed for maximum of 90°C through branch circuit conductors. Integral
cable clamps permit attachment of non-metallic (#12 or #14 ga.) Romex®
cable without tools or additional connectors.
4. Mounting Bars: .059” (#16 ga.) galvanized steel. Bars pivot for easy
attachment and wire-in below ceiling line. Bars extend to accommodate
16” to 24“ O.C. joist spacing. Bars can accommodate 12” O.C. joist spacing
after a slight field modification (see Instruction Sheet). 1004ICV features
integral self tapping phillips screws for secure attachment to wood or metal
construction. 1004ICVN features integral nails for secure attachment to
wood. Both ends at tach to T-bar ceilings without the need of accessories.
5. Socket Housing: .036” (#20 ga.) galvanized steel.
6. Socket: Field replaceable. Two pin socket, pre-wired with #18 SF1 leads to
junction box.
7. Thermal Protector: Meets NEC and UL requirements (integral to
transformer). Located inside housing.
8. Transformer: Mounted inside housing, magnetic. 120V primary, nominal 12V
secondary. Removable from below.
Dimming UL
Dimming Controls: Use only dimmers specifically designed for use with mag-
netic transformers, like Lightolier Onset® Sunrise® series LV or VA, dimmers,
or any Lightolier Controls dimming systems. Low voltage fixtures may produce
audible sound which may be objectionable in acoustically critical areas.
Options & Accessories
Extra-Thick Ceiling
Mounting Ring: 1967B - 1 1/4” to 2” thick ceilings.
MR 16 Socket Replacement: 1975 A
Socket for General Electric Turn
and Lock (TAL) MR16 Lamp: 1975 TAL
Labels
UL (Type I.C., Suitable for Damp Location), I.B.E.W.
Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.
AirSeal® is a registered trademark of ALCOA.
Romex® is a registered trademark of General Cable Industries Inc.
US Patents numbers: 6,272,744; 6,369,326
Job Information Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
www.lightolier.com © 2008 Philips Group • E1108
Lightolier is a Philips group brand
Loading...