READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:1104ICN
C1204 |
Page 1 of 2 |
|
|
|
INSTALLATION |
|
|
|
|
FOR CONVERTIBLE IC/NON IC |
||||||
|
|
|
FRAME |
|
|
|
|
|
|
1104ICN, 1104SICN |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fig. A |
Fig. B |
Fig. D |
Fig. E |
Fig. F |
Frame-In |
Wire-In |
Close-In |
Snap-On |
Push-Up |
For IC Installations:
Remove the peel off label on the outside of the housing section.
CONVERTIBLE IC/NON-IC HOUSING
IC APPLICATIONS: REMOVE THIS WARNING LABEL. SEE INSTRUCTION SHEET.
NON-IC APPLICATIONS:
WARNING - RISK OF FIRE.
DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDE OR WIRING COMPARTMENT NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HEAT.
For Non-IC Installations:
the lower portion of -IN LABEL as shown.
rough-in sections are higher wattage lamps.
SOCKET CUP
ROUGH-IN LABEL
1.FRAME-IN (Fig. A)
Locate fixture along joist and line up bottom edge of HINGED MOUNTING BAR with the bottom of joist and fasten in place.
HINGED MOUNTING BAR
For suspended ceilings:
•Rotate HINGED BAR ENDS to position shown and fully extend bars.
•Crimp bottom of edge of CHANNEL to prevent rotation of HINGED BAR ENDS.
•Bend NON-HINGED end of mounting bar at featured hole location and extend out.
•Position notched area of MOUNTING BARS onto T-BAR and lock by bending TAB underneath T-BAR BEAD as shown.
|
HINGED BAR ENDS |
T-BAR |
|
CHANNEL |
|
3” |
1004IC |
TAB |
|
3 3/4” 1104IC
BEND AT HOLE
TAB
5 1/4” 1004IC
6 1/4” 1104IC
BEND TAB
TO LOCK
® |
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720