Lightolier 1001FDIC User Manual

Performance Recessed CFL Downlighting 1001FDIC

1

2

3

4

5

6

7

Reflector Trim

Frame-in Kit

Page 1 of 1 5" Aperture, 1 Light, Compact Fluorescent, IC AirSeal®, Dimming, Frame-In Kit

Overall Length

15 5/16"

12 1/4"

13" Min.

24" Max.

Height: 7 1/4"

Ceiling Opening: 5 1/4"

Top View

Complete Fixture consists of Frame-In Kit and Reflector Trim. Select each separately.

Uniframe™
Frame-In Kit

1001FDICMX1**

(Advance Mark10 – 120v)

26 w Triple

GX24q-3 Base
120v – 0.26amp max

1001FDICMX2**

(Advance Mark10 – 277v)

26 w Triple

GX24q-3 Base
277v – 0.11amp max

**Add N to catalog number

for preset nails.

Uniframe

Horizontal Open Horizontal Wall

100 1HCL
100 1HCD
100 1HWH

Universal Series Reflector Trims (Reference Trim Spec Sheet for Recommended Lamping)

Cone Satin Cone Bafe Wall Wash Wet Location

1012* 1071
1013* 1045

1013BK* 1046
1013WH 1046CD
1013CD*

™

Compact Fluorescent Performance Series Reflector Trims

Horizontal Wet Location

Wash - Single

100 1HCLSW
100 1HCDSW
100 1HWHS W

Lensed / Diffused

Clear Lens Fresnel

100 1HCLC 100 1HCLF
1001HCDC 1001HCDF
100 1HWHC 100 1HWHF

Opal Lens

100 1HCLO
1001HCDO
100 1HWHO

1008*

1010*

100 5*
1005BNM
1005WH

1076
1076W H

Overall Width

10 3/8"

Horizontal
Cross Blade

100 1HACB
100 1HWHCB

1035
1035WH
1085
1095
1096
1096CD

1024
1078

*Add NM sufx to catalog number
for Natural Metal ange and nish.

Features

1. Housing: .028" (#21ga.) aluminum. UL listed for direct contact with thermal

insulation. AirSeal® housing minimizes air leakage to less than 2 CFM at 1.57
PSF (or 75pa), which complies with Model Energy Code (Section 602.3.3) and
Washington State Energy Code (Section 502.4) and reduces heat loss and
condensation in ceiling. Access door for inspection of junction box.

2. Mounting Frame: .032 (#22 ga.) galvanized steel. Accommodates ceilings
up to 1 1/2" thick. 3/8" deep integral lip. Locks into position along length
of mounting bars with locking screw and bendable slot. Four slots are
positioned 90° apart to simplif y alignment. Push-in/twist-out roto-clips hold
reflector flush to ceiling.

3. Junction Box: 2" X 4" X 3 1/2" (22 cu. in) .032" (#22 ga.) galvanized steel. UL
listed for maximum of 8 (#12 ga.) 90°C through branch circuit conductors.

4. Mounting Bars: .059" (#16 ga.) galvanized steel. Bars pivot for easy
attachment and wire-in below ceiling line. Bars extend to accommodate 16"
to 24" O.C. joist spacing. Bars can accommodate 12" O.C joist spacing after
a slight field modification (see Instruction Sheet). Features integral self
tapping phillips screws for secure attachment to wood or metal construction.
Attaches to T-bar ceilings without the need of accessories.

5. Ballast: Mounted inside housing. 120V or 277V UL Listed Electronic Dimming
Ballast, end of lamp life protection, class “P” thermally protected, class “A”
sound rating.

6. Socket: Four-pin base, molded thermoplastic socket, prewired with No. 18
AWM leads to ballast.

7. Socket Housing: .036" (#20ga.) Galvanized Steel housing attaches to
reflector trim by spring clip for precise optic alignment.

Lightolier is a Philips group brand

Options & Accessories

Extra-Thick Ceiling
Mounting Ring: 1967B - 1 1/4" to 2" thick ceilings

Labels

cULus Listed (Type I.C., Suitable for Damp Location), I.B.E.W.

Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.

®

is a registered trademark of Lightolier

AirSeal

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:

631 Airport Road, Fall River, MA 02720 • [phone] • Fax [phone]

We reserve the right to change details of design, materials and finish.

www.lightolier.com © 2008 Philips Group • D0708