lightMoods MNFLSC-24V-72 User Manual
Single End Connection Application Accessories Kit
01 (o r 02) Fro nt Conn ector
Sil icon Ga sket
U Ste el Plat e
Ant i-ski dding C lip
1 pc
1 pc
1 pc
1 pc
Fro nt Conn ector Ac cesso ries Ki t
End C ap Acces sorie s Kit
The Tai l Pl ug
U Ste el Plat e
Ant i-ski dding C lip
Sil icon Ga sket
1pc
1pc
1pc
1pc
Fig. 1 Minim um b ent dia me ter 90m m
Ligh t Surfa ce
Φ90m m
LightMoods
TM
MINI Flat LED Neon Ribbon Light
USER MANUAL
MNFLSC-24V-72
(Green/Blue/Warm White/White/Cool White/Daylight White)
1. Model: MNFLSC-24V-72
2. Rated input voltage: DC 24V
3. Rated Power: 5W/m
4. Dimension: 9*18mm
5. LED quantity: 72LEDs/mtr
6. LED Spacing: 13.88mm
7. Min. cutting length: 83.3mm( 6LEDs)
8. Max. running length: 15 mtrs for single end feed or 30mtrs
for double ends feed.
9. Light color: Single Color
(Green/Blue/Warm White/White/Cool White/Daylight White)
10. Min. bent diameter: 90mm; Do not twist the light .
11.Protection rate: IP68
12.Protection rate for IP68: Protected against dust and submersion
in water (1meter above).
NOTE: All connector joints must be connected correctly to achieve
IP68 rating
13.Can be cut and extended
14.Long lifetime: 5 years
15.Working ambient temperature: -4°~113°F (-20°~45°C)
16.Operating (bending) ambient temperature: 32°~113°F (0°~45°C)
Palm Coast, Florida, USA / Los Angeles, California, USA / Pribram, Czech Republic / Birmingham, U.K. / Kuala Lumpur, Malaysia / Mumbai, India
Email: christian@aveoengineering.com / Web: www.aveoengineering.com
DO-160G
tested
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION AND LEAVE A COPY FOR THE END
USER/MAINTENANCE ENGINEER FOR FUTURE REFERENCE
FEATURES WARNING AND CAUTION
ACCESSORIES (SOLD SEPARATELY)
ASSEMBLY AND INSTALLATION
FIGURES
WARNING
1. Before making any cuts,installation,maintenance or connection, be sure
the mains is disconnected!
2. NOTE: ALL CONNECTOR JOINTS MUST BE CONNECTED CORRECTLY TO
ACHIEVE IP68 RATING.
3. Please operate this ex light according to the instructions, and conrm
the work voltage, it must be matched with product requirements.
4. Please conrm the polarity of connector before insertion front connection cable.
5. Connect and cut this product correctly. Any wrong operation will damage this
product.
6. No pressing on this product during storage, long term pressing may lead to damage.
7. Using qualied DC power supply.
8. Min. bent diameter 90mm, see Fig.1.
9. Do not twist the light as Fig.2 and follow the correct bending direction as Fig.3.
10. Do not hang this light in the air as Fig.4.
11. Cutting at the wrong location will result in a failure of the light! See Fig.5.
CAUTION
1. Suitable for mounting on normally ammable surfaces..
2. Use only factory-recommended connectors and accessories.
3. To ensure its long life span, operate the light properly in accordance with the
instructions.
4. Do not operate in more than 113°F (45°C) ambient temperature.
5. Assemble the DIY Connector correctly as in Fig.6.
6. Max. running length depends on the energizing way as Fig.7 shown.
7. Warm White,Cool White and Daylight color reference ANSI STANDARD.
8. Do not operate light when ambient temperature is below 32°F (0°C) thais may injure
the light .
1. Turn o the electricity before operation.
2. Cut the light at correct location (if need).
3. Assemble the light according to Fig.8.
4. Install U channel and light according to Fig.9 (Only applicable to DIY accessories) .
5. Wire all connectors to the power line and check wiring of the whole circuit.
Cable color coding basics Refer to Fig.10.
×
×
Fig. 5 Unit cu tt ing gui de
(Onl y ap plica bl e to DIY ac ce ssori es )
Pay at tenti on to ”+” bot h
on lig ht bo dy and fr ont
conn ect or
Lig ht Surf ace
√
Lig ht Surf ace
×
×
Lig ht Surf ace
×
√
Fig. 2 Fig. 3
Rec ommen ed Use
Lig ht Surf ace
Lig ht Surf ace
Lig ht Surf ace
PCB
LED
PVC
83. 3mm
Cut ting li ne
√
×
×
The co rr ec t cu tting way,R= 90°
Wav e cu tt ing is inco rr ec t
R=90°is in co rr ect
√
×
Connector Pin s
√
×
Connector Pin s
√
×
Connector Pin sConnector Pin s
For 01 Type F ro nt Conn ec tor
MINI Flat LED Neon Ribbon Light
USER MANUAL
MNFLSC-24V-72
(Green/Blue/Warm White/White/Cool White/Daylight White)
Palm Coast, Florida, USA / Los Angeles, California, USA / Pribram, Czech Republic / Birmingham, U.K. / Kuala Lumpur, Malaysia / Mumbai, India
Email: christian@aveoengineering.com / Web: www.aveoengineering.com
DO-160G
tested
2
Twisting the light is forbidden and observe to correct
bending orientation
Fig. 4 Installation of the light hanging suspended in the air as
the picture illustrates is forbidden.
Fig.6 Correct insertion of connector pins
LightMoods
TM
Loading...