Light Emotion P64LEDLITEWW User Instruction Manual

1 of 6 pages

WWW.LIGHTEMOTION.COM.AU

P64LEDLITEWW

183 Warm White LEDs

User’s instruction manual

This manual contains important information about the safe installation and use of this product

Please read this instruction manual carefully before installing or operating

Please keep these instructions in a safe place for future reference

2 of 6 pages

Congratulations on the purchase of your P64LEDLITEWW by Light Emotion. We are confident that you will
be satisfied with your purchase. We have prepared this manual to assist you with the care and operation of this
item.

CONTENTS

SECTION Page

WHAT IS INCLUDED, SAFETY INSTRUCTION

2

POWER, FUSE, FEATURES, INSTALLATION 3
MAINTENANCE & PERIODIC CHECKS, CONNECTIONS AND CONTROLS, DIP SWITCHES 4
DMX LEADS, DMX TERMINATORS, STANDALONE, MASTER/SLAVE MODE 5
DMX CHANNEL INFORMATION, DMX MODE, FAQ 6
SPECIFICATIONS

7

Please note that as part of our ongoing commitment to continuous improvement and product
development, the specifications in this manual are subject to change without notice. Whilst every
care has been taken in the preparation of this manual we reserve the right to change specifications in
the course of product improvement.

WHAT IS INCLUDED:

CAUTION: Do not use sharp objects whilst unpacking this product

• 1x P64LEDLITEWW lighting effect

• 1x Manual

SAFETY INSTRUCTIONS:

Please read these instructions carefully. It includes important information about the installation
usage and maintenance of this product.

• Please keep this User Manual for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

• Always make sure that you are connecting to the proper voltage and that the line voltage you

are connecting to is not higher than that stated on the rear panel of the fixture.

• This product is intended for indoor use only! To prevent risk of fire or shock, do not expose

fixture to rain or moisture.

• Make sure there are no flammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surface. Be sure that no ventilation slots are blocked.

• Always disconnect from power source before servicing or replacing fuse and be sure to

replace with same fuse source.

• Secure fixture to fastening device using a safety chain.

• Maximum ambient temperature is 40˚C. Do not operate fixture at temperatures higher than

this.

• In the event of serious operating problem, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center.

• Never connect the device to dimmer pack.

• Make sure power cord is never crimped or damaged.

• Never disconnect power cord by pulling or tugging on the cord.

• Never carry the fixture directly from the cord. Always use the hanging/mounting bracket.

• Avoid direct eye exposure to the light source while it is on.

3 of 6 pages

POWER

CAUTION: This lighting effect is designed to operate at 240V.

Power Consumption: 30W

FUSE

CAUTION:

Only use the correct fuse as specified on the rear panel of the lighting effect.
Disconnect the lighting effect from the mains before attempting to replace the
fuse.

To replace the fuse please follow the following steps:

1. Remove the fuse by unscrewing the cap out with a screwdriver. (Refer to Fig 1)

2. Remove existing fuse.

3. Fit new fuse.

4. Refit the fuse holder.

Fuse: M205 0.5A fast

FEATURES

Warm White LED par can
Dimming and strobing
DMX-512 controllable with 2 channels

INSTALLATION

CAUTION: For safe mounting read the following instructions carefully.

• Use suitable hook clamps* for hanging the lighting effect.

• Use a safety wire* with a breaking strain of more than double the

lighting effect.

• Do not look directly into the light source.

• Make sure the lighting effect has suitable ventilation as per the

instructions below.

• This lighting effect is intended for indoor use only.

• To avoid electrical shock keep away from rain and moisture.

• Keep unit out of reach from children.

NOTE:

Use washers* and spring washers* when attaching your hook clamp* to the yoke.

1. For installation of the hook clamps* and safety wire* please refer to Fig 2.

2. This lighting effect must be 0.5m away from any flammable materials or any walls or ceilings.

3. Do not block or inhibit the air flow from the ventilation holes.

Light Emotion have various hook clamps* and safety wires* suitable for your product. Please
contact your local dealer for more information *Not included.

Fig.1

Fig.2