Light Emotion P64100RGB User Instruction Manual

WWW.LIGHTEMOTION.COM.AU

P64100RGB

User’s instruction manual

This manual contains important information about the safe installation and use of this product

Please read this instruction manual carefully before installing or operating

Please keep these instructions in a safe place for future reference

www.lightemotion.com.au

2

Congratulations on the purchase of your P64100RGB by Light Emotion. We are confident that you will
be satisfied with your purchase. We have prepared this manual to assist you with the operation of this
item.

CONTENTS

SECTION Page

WHAT IS INCLUDED, SAFETY INSTRUCTION 2
POWER, FUSE, INSTALLATION 3
MAINTENANCE & PERIODIS CHECKS, DMX LEAD, DMX TERMINATOR, FEATURES 4
OPERATION 5

SPECIFICATIONS 11

Please note that as part of out ongoing commitment to continuous improvement and product
development, the specifications in this manual are subject to change without notice. Whilst every care
has been taken in the preparation of this manual we reserve the right to change specifications in the
course of product improvement.

WHAT IS INCLUDED:

CAUTION:

Do not use sharp objects whilst unpacking this product

•

1x P64100RGB

•

1x Warranty Card

•

1x User Manual

Please note: Some of the items above may be fitted to the product by the manufacturer.

SAFETY INSTRUCTIONS:

Please read these instructions carefully. It includes important information about the installation usage
and maintenance of this product.

•

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.

•

Always make sure that you are connecting to the proper voltage and that the line voltage you are
connecting to is not higher than that stated on the rear panel of the fixture.

•

This product is intended for indoor use only! To prevent risk of fire or shock, do not expose
fixture to rain or moisture.

•

Make sure there are no flammable materials close to the unit while operating.

•

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surface. Be sure that no ventilation slots are blocked.

•

Always disconnect from power source before servicing or replacing fuse and be sure to replace
with same fuse source.

•

Secure fixture to fastening device using a safety chain.

•

Maximum ambient temperature is 40˚C. Do not operate fixture at temperatures higher than this.

3

•

In the event of serious operating problem, stop using the unit immediately. Never try to repair
the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center.

•

Never connect the device to dimmer pack.

•

Make sure power cord is never crimped or damaged.

•

Never disconnect power cord by pulling or tugging on the cord.

•

Never carry the fixture directly from the cord. Always use the hanging/mounting bracket.

•

Avoid direct eye exposure to the light source while it is on.

POWER:

CAUTION:

This lighting effect is designed to operate at 240V. Power Consumption: 90W

FUSE:

CAUTION:

Only use the correct fuse as specified on the rear panel of the
lighting effect.
Disconnect the lighting effect from the mains before attempting to
replace the fuse

NOTE:

This lighting effect has a position for a spare fuse located in the fuse
holder toward the outside of the fixture
To replace the fuse please follow the following steps

1. Remove the fuse holder by levering the holder out with a
screwdriver

2. Remove existing fuse

3. Fit new fuse

4. Refit the fuse holder

INSTALLATION:

CAUTION:

For safe mounting read the following instructions

carefully.

• Use suitable hook clamps* for hanging the lighting effect.

• Use a safety wire* with a breaking strain of more than

double the lighting effect.

• Do not look directly into the light source.

• Make sure the lighting effect has suitable ventilation as per

the instructions below.

• This lighting effect is intended for indoor use only.

• To avoid electrical shock keep away from rain and

moisture.

• Keep unit out of reach from children.

4

NOTE:

Use washers* and spring washers* when attaching your hook clamp* to the yoke.

1. For installation of the hook clamps* and safety wire*.

2. This lighting effect must be 0.5m away from any flammable materials or any walls or ceilings.

3. Do not block or inhibit the air flow from the ventilation holes.

Light Emotion have various hook clamps* and safety wires* suitable for your PAR 64LED Please
contact your local dealer for more information
*Not included.

MAINTENANCE & PERIODIC CHECKS:

CAUTION:

Some maintenance and checks may require the product to be opened and should only be done by
qualified persons. Warranty may be void if damage has been caused by improper maintenance.

DMX LEAD:

The DMX lead is used to link up multiple units.

DMX TERMINATOR:

A DMX terminator helps to reduce ‘noise’ on the DMX chain, and makes the light respond to control
more accurately. It should be plugged in to the last fixture in any chain.

FEATURES:

Manual dimmer color mode
Sound active mode
Auto-run program mode
Static color select mode
Master /Slave mode
DMX mode

DMX512

PIN FUNCTION

1 GND
2 DATA
3 DATA +