Light Emotion FLAT1212 Instruction Manual

WWW.LIGHTEMOTION.COM.AU

FLAT1212

User’s instruction manual

This manual contains important information about the safe installation and use of this product

Please read this instruction manual carefully before installing or operating

Please keep these instructions in a safe place for future reference

www.lightemotion.com.au

2

Congratulations on the purchase of your FLAT1212 by Light Emotion. We are confident that you will
be satisfied with your purchase. We have prepared this manual to assist you with the operation of this
item.

CONTENTS

SECTION Page

WHAT IS INCLUDED, SAFETY INSTRUCTION 2
POWER, FUSE, INSTALLATION 3
MAINTENANCE & PERIODIS CHECKS, DMX LEAD, DMX TERMINATOR, FEATURES 4
OPERATION 5

SPECIFICATIONS 9

Please note that as part of out ongoing commitment to continuous improvement and product
development, the specifications in this manual are subject to change without notice. Whilst every care
has been taken in the preparation of this manual we reserve the right to change specifications in the
course of product improvement.

WHAT IS INCLUDED:

CAUTION:

Do not use sharp objects whilst unpacking this product

•

1x FLAT1212

•

1 x Power Lead

•

1x Warranty Card

•

1x User Manual

Please note: Some of the items above may be fitted to the product by the manufacturer.

SAFETY INSTRUCTIONS:

Please read these instructions carefully. It includes important information about the installation usage
and maintenance of this product.

•

Please keep this User Manual for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.

•

Always make sure that you are connecting to the proper voltage and that the line voltage you are
connecting to is not higher than that stated on the rear panel of the fixture.

•

This product is intended for indoor use only! To prevent risk of fire or shock, do not expose
fixture to rain or moisture.

•

Make sure there are no flammable materials close to the unit while operating.

•

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surface. Be sure that no ventilation slots are blocked.

•

Always disconnect from power source before servicing or replacing fuse and be sure to replace
with same fuse source.

•

Secure fixture to fastening device using a safety chain.

•

Maximum ambient temperature is 40˚C. Do not operate fixture at temperatures higher than this.

3

•

In the event of serious operating problem, stop using the unit immediately. Never try to repair
the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center.

•

Never connect the device to dimmer pack.

•

Make sure power cord is never crimped or damaged.

•

Never disconnect power cord by pulling or tugging on the cord.

•

Never carry the fixture directly from the cord. Always use the hanging/mounting bracket.

•

Avoid direct eye exposure to the light source while it is on.

POWER:

CAUTION:

This lighting effect is designed to operate at 240V. Power Consumption: 105W

FUSE:

CAUTION: Only use the correct fuse as specified on the

rear panel of the lighting effect. Disconnect the lighting
effect from the mains before attempting to replace the
fuse.

To replace the fuse please follow the following steps:

1. Remove the fuse holder cover with a screwdriver.

2. Remove existing fuse.

3. Fit new fuse.

4. Refit the fuse holder.

Fuse: M205 2A slow blow

INSTALLATION:

CAUTION:

For safe mounting read the following instructions

carefully.

• Use suitable hook clamps* for hanging the lighting effect.

• Use a safety wire* with a breaking strain of more than

double the lighting effect.

• Do not look directly into the light source.

• Make sure the lighting effect has suitable ventilation as per

the instructions below.

• This lighting effect is intended for indoor use only.

• To avoid electrical shock keep away from rain and

moisture.

• Keep unit out of reach from children.

NOTE:

Use washers* and spring washers* when attaching your hook clamp* to the yoke.

1. For installation of the hook clamps* and safety wire*.