Lightcomm Technology CSPBTF1 User Manual
NS-CSPBTF1_16-0030_QSG_V2_EN.ai 2 4/6/2016 7:53:23 AM
Audio cable
• Connect a 3.5 mm audio cable (not
included) from your speaker’s AUX IN
jack to your audio device’s
headphone/audio out jack.
USING YOUR
SPEAKER
Listening to audio
1 Play audio on your connected device.
2 Press + or - to adjust your speaker’s
volume.
Note: Make sure that your connected
device’s volume is set to at least 50%.
3 Use the controls on your connected
device to control playback.
TAKING A PHONE
CALL
The following functions are available when
paired to a phone with Bluetooth:
• Reject an incoming call: Press and hold
(call).
• Answer an incoming call: Press
(call).
• Switch audio between your speaker and
phone: Press and hold (call).
• End current call: Press (call).
edial the last dialed number: Press
• R
(call) twice.
LED INDICATORS:
LED
Blinks blue
quickly
Lights solid blue
Blinks blue
slowly
Lights red
FUNCTION
Bluetooth pairing mode
Paired to a Bluetooth
device
Connected to an
AUX device
Speaker is charging
(charging complete
TROUBLESHOOTING
Unable to pair.
• If a passcode is needed, enter 0000.
• Move your speaker and Bluetooth device
closer together.
Static or breaks while playing audio.
• Move your speaker and Bluetooth device
closer together.
• Use a paper clip to press reset.
• Make sure that the audio cable is
connected securely.
No sound.
• Turn up the volume on both your speaker
and connected device.
• Make sure that your Bluetooth device is
paired to your speaker.
• Unplug the audio cable (if connecting
with Bluetooth).
No power.
• Make sure that your speaker is fully
charged.
Unable to operate.
• Use a paper clip to press reset.
LEGAL NOTICES
lf at any time in the future
you should need to dispose of
this product, note that waste
electrical products should not
be disposed of with household waste.
Recycle where facilities exist. Check with
your Local Authority or retailer for
recycling advice. (Waste Electrical and
Electronic equipment Directive)
Owing to continuous improvement, no
prior notice will be given regarding
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to
try correct the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
WARRANTY
Visit www.insigniaproducts.com for
details.
CONTACT
INSIGNIA:
For customer service, call 1-877-467-4289
(U.S. and Canada) or 01-800-926-3000
(Mexico)
www.insigniaproducts.com
companies.
Distributed by Best Buy Purchasing, LLC
©2016 Best Buy. All rights reserved.
Made in China
V2 ENGLISH 16-0030
Loading...