Lifetime 2129 Assembly Instructions And Owner's Manual

Download

Copy

VISIT THE LIFETIME WEB SITE:

WWW.LIFETIME.COM

6-PERSON ROUND

PICNIC TABLE

MODEL #2129

ASSEMBLY INSTRUCTIONS AND OWNER’S

MANUAL

Save this instruction in the event that the manufacturer

has to be contacted for replacement parts.

INSTRUCTION #1017715 11/03/2006

WARNING

To ensure your safety, do not attempt to assemble the table without reading and following all inst ructi ons and warnings carefully.

BEFORE BEGINNING ASSEMBLY

A. Identify and inventory all parts using the checklist boxes on the Parts List.

SAFETY INSTRUCTIONS

FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE.

• Proper and complete assembly and use is essential for proper operation and to reduce the risk of injury.

• 2 people are required for assembly.

• If technical assistance is required, contact the manufacturer.

• Most injuries are caused by misuse and/or failure to follow instructions.

PARTS LIST

ID Part # Description Qty

AA 1007361 Table Top (1003645) 1 AB 1007365 Bench (1003635) 3 AC ZP97506 Table Leg 3 AD ZP97606 Center Table Leg Brace 3 AE ZP97706 Bench Leg 3 AF ZP97806 Bench Frame 3 AG ZP97906 Bench Leg Pivot 3 AH 1007362 Footcap 6 AI 1008729 Plug, Umbrella Hole 1 AJ 1007363 Bench Leg Cap 6 AK 1019483 Support Brace 1 3 AL 1019484 Support Brace 2 3

Table Frame Hardware (1020883)

RA BS03300 1/4” x 1/2” Screw 6 RC 1004700 5mm Cap Nut 12 RD 1004641 5mm Flat Washer 3 RE 1008307 #8 x 1/2” Screw 21

Bench Frame Hardware (1020884)

RA BS03300 1/4” x 1/2” Screw 18 RE 1008307 #8 x 1/2” Screw 12 BA 1016552 5mm x 12.5mm Carriage Bolt 24 BB 1003781 M5 Centerlock Nut 24 BD 1013012 Cotter Key 3

If two or more people are sitting at the table at the same time, we recommend they sit across the table from each other to prevent possible tipping of the table.

TWO ADULTS ARE NECESSARY TO

COMPLETE ASSEMBLY!!

Tools and Materials Required

For Assembly

(Not Included)

1. Adjustable Wrench

2. 5/16” Wrench

3. Phillips Screwdriver

Footcaps on Table Legs

Step 1 Hardware

Turn a Table Leg (AC) upside down. Place a Footcap (AH) on the bottom of each leg. Secure the each Footcap with two (2) #8

x 1/2” Screws (RE). Repeat for remaining two legs.

Assemble Legs

Turn Table Legs right side up. Attach one (1) Center Leg Brace

(AD) to each table leg as shown. Ensure the end of brace angles upwards. Secure with two (2) #8 x 1/2” Screws (RE). Repeat for remaining Legs.

Completely tighten both Screws, then loosen them one (1) full

Hardware Bag: 1020883

Step 2 Hardware

Hardware Bag: 1020883

RE (12)

Screwdriver

RE (9)

Screwdriver

Stand Table Legs assemblies in circle with braces pointing in

towards the center.

Note: Completely tighten both Screws (RE), then loosen them one

(1) full turn.

Note: The Center Leg Braces are joined together always in a Right over Left format.

While standing between two legs, line up the end hole on the right brace with the middle hole on the

left brace as shown. Secure with one (1) #8 x 1/2” Pan Head Screw (RE).

Note: Do not completely tighten the Screws (RE) yet.

Move Clockwise and stand between the next pair of legs. Line up the end hole on the right brace with

the middle hole on the left brace as shown. Secure with one (1) #8x 1/2” Pan Head Screw (RE).

Note: Do not completely tighten the Screws (RE) yet.

Move Clockwise and stand between the last pair legs. Line up the end hole on the right brace with the

middle hole on the left brace as shown. Secure with ine (1) #8 x 1/2” Pan Head Screw (RE). Set aside

Note: Do not completely tighten the Screws (RE) yet.

assembly.

Support Braces to Table Top

Two sets of three (3) Support Braces (AK & AL) come with your picnic table. Set AK comes with two bolts next to each other (one of the bolts is gold colored). Set AL comes with two bolts about 12” from each other.

Gold Colored Bolt

Step 3 Hardware

Hardware Bag: 1020883

RA (1)

Screwdriver

Place a Support Brace (AK) onto the underside of the Table Top and lightly secure the Brace with one

1/4” x 1/2” Screw (RA).

Note: Do not completely tighten the Screw (RA) yet.

Pilot Hole

Underside of Table

Place a Support Brace (AL) over Support Brace (AK) and lightly

secure the Brace to the Table Top with one (1) 1/4” x 1/2” Screw

(RA).

Note: Do not completely tighten the Screw (RA) yet.

Pilot Hole

Step 3 Hardware

Hardware Bag: 1020883

RA (2)

Screwdriver

Note: Do not completely tighten the Screw (RA) yet.

Underside of Table

Pilot Hole

Underside of Table

Note: Do not completely tighten the Screw (RA) yet.

Step 3 Hardware

RA (2)

Note: Do not completely tighten the Screw (RA) yet.

Hardware Bag: 1020883

Pilot Hole

Underside of Table

Screwdriver

Underside of Table

Pilot Hole

Remove the rst 1/4” x 1/2” Screw (RA) and gently tilt the Support

Brace (AK) and slide the last Support Brace (AL) into place.

Replace the rst 1/4” x 1/2” Screw (RA) into the rst Support Brace (AK). Finally, secure the last Support Brace (AL) to the Table Top.

Completely tighten all Screws (RA).

Step 3 Hardware

RC (3)

Hardware Bag: 1020883

RA (1)

RD (3)

Screwdriver

Adjsutable Wrench

Pilot Hole

Underside of Table

Secure Support Braces AL to AK using three (3) 5mm Washers and three (3) 5mm Cap Nuts.

CAUTION

Do not overtighten Screws (RA). Ov erti ghte ning may damag e parts and void warranty.

Completely tighten all Cap Nuts (RE).

Underside of Table

WARNING

Do not overtighten the Cap Nut. If the end of the Bolt breaks through the plastic cap, call our Customer Service Department at the number on Page One. Exposed threads on the end of the Bolt may cause serious injuries.

Legs to Support Braces

Step 4 Hardware

With the Table Top facing top down on the ground, align the Leg

assembly (Step 2) over the three sets of bolts on the Support

Brace assembly. Fasten the Leg assembly to the Support Braces using

nine (9) 5mm Cap Nuts (AC). Tighten all hardware (including the Center Braces from Step 2). Stand the Table upright.

Note the set of three bolts.

RC (9)

Hardware Bag: 1020883

Adjustable Wrench

WARNING

Assemble Benches

(Repeat This Step for all 3 Benches)

Turn a Bench Leg (AE) upside-down and fasten a Bench

Leg Cap (AJ) on each end of the foot. Secure each Cap to the legs with two (2) #8 x 1/2” Screws (RE).

Step 5 Hardware

Hardware Bags: 1020884

RE (12)

Screwdriver

Lay a Bench Frame (AF) top-side down, with curved

edges pointing away from you.

Step 5 Hardware

BB (24)

BA (24)

RA (18)

Hardware Bags: 1020884

Line up a bench leg with the right side of the Bench Frame (AF). Secure to frame with four (4) 5mm x

12.5mm Carriage Bolts (BA) and four (4) M5 Centerlock Nuts (BB).

Bench Leg

Screwdriver

Adjustable Wrench

Line up a Bench Leg Pivot (AG) piece with the left side of the

bench seat frame. Secure to frame with four (4) 5mm x 12.5mm Carriage Bolts (BA) and four (4) Centerlock Nuts (BB).

Frame

Note: The tab on the frame

must line up with the hole in the Bench Leg plate.

Bench Leg

Frame

Note: The tab on the frame

must line up with the hole in the Bench Pivot plate.

Lay a Bench (AB) top-side down, with curved side pointing away from you. Lay Bench Frame inside the

Bench and line up holes. Repeat for all three benches.

Fasten the Bench Frame to the Bench with six (6) 1/4” x 1/2” Screws (RA).

Only use a hand screwdriver on this step

Attach Bench to Table

(Repeat Steps 6a and 6b for all 3 Benches)

Insert a Bench assembly into the table leg. Ensure the bench is

fully inserted into the leg.

Note: Ensure that the holes line-up with the pilot holes in the Bench.

Step 6 Hardware

BD (3)

Hardware Bag: 1020884

Insert a Cotter Key (BD) through the two holes in the leg of the bench to help prevent the bench from

pulling out of the Table Leg.

Insert Umbrella Hole Plug

If the Umbrella Hole Plug is not already installed, snap it into the hole at the center of the table.

PICNIC TABLE CARE INSTRUCTIONS

• Surface may be hot if left in sun. • Do not place a direct heat source on or near the surface unless using a heat barrier • Do not stand on table or benches. • Do not sit on table • Do not tip table on edge or bench may fall and cause injury • Lift table by the tabletop • Do not lift table by the benches • Failure to comply with these warnings could result in serious personal injury

WARNING

• La surface peut etre chaude en cas d’exposition au soleil.

• Ne placez pas de source de chaleur directement sur ou près de la table sans utiliser de quoi protéger la table de la chaleur • Ne pas se mettre debout sur la table ou sur les bancs • Ne vous reposez pas sur le tableau • Ne mettez pas la table sur le bord ou les bancs peut tomber et peut causer des blessures • soulevez la table par le panneau de la table • Ne soulevez pas le table par les bancs • Le non respect de ces mises en gardes pourrait entrainer des blessures graves

• La supercie puede estar caliente si se ha dejado expuesta

al sol. • No coloque una fuente directa de calor sobre la

supercie de la mesa o cerca de la misma sin usar una

protección contra el calor • No se pare sobre la mesa ni sobre los bancos • No se siente sobre la mesa • No ponga la mesa en el borde o el banco puede caer y puede ser causa lesiones personales • Levante la mesa por el tablero de la mesa • No levante la mesa por los bancos • El no respetar estas advertencias puede ser causa de serias lesiones personales

WATCH FOR PINCH POINTS EVITEZ LES RISQUES DE PINCEMENT CUIDESE DE LOS PUNTOS DE PUNZANTES

#1008736

ADVERTENCIA

AVERTISSEMENT

Congratulations on your Lifetime purchase. By following the instructions below, your new Lifetime table should provide you with years of service and enjoyment.

Cleaning and Care

The polyethylene tabletop and benches are stain- and solvent-resistant. To clean, use a mild soap and a softbristled brush. Abrasive cleaning materials may scratch the plastic and are not recommended. Repair scratches or rust spots on the metal frame by sanding the affected area lightly; using a rust-preventative spray primer; and

nally, spraying with a high-gloss spray enamel paint. Avoid placing a direct heat source on or near the table

surface unless using a heat barrier.

PICNIC TABLE

10-YEAR LIMITED FACTORY WARRANTY

LIFETIME PRODUCTS, INC. RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF

PARTS ARE UNAVAILABLE OR OBSOLETE.

1. Lifetime Picnic Tables are warranted to the original purchaser to be free from defects in material or

workmanship for a period of ten years from the date of original retail purchase. The word “defects” is dened as

imperfections that impair the use of the product. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to alteration or accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the control of the manufacturer.

2. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product. If the product is defective within the terms of this warranty, Lifetime Products, Inc. will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory are not covered and are the responsibility of the purchaser.

3. This warranty does not cover scratching, scufng or other cosmetic damage that may result from normal

use of the product. In addition, defects resulting from intentional damage, negligence or unreasonable use will void this warranty.

4. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the highest degree of safety in all products, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.

5. This warranty is in lieu of all other warranties expressed or implied, including warranties of merchantability

or tness for use. Neither Lifetime Products, Inc. nor any representative assumes any other liability in connection

with this product.

ALL WARRANTY CLAIMS MUST BE ACCOMPANIED BY A SALES RECEIPT.

REPORT PRODUCT DEFECTS IN WRITING TO:

Lifetime Products, Inc., PO Box 160010 Cleareld, UT 84016-0010

or call 1(800) 225-3865

Lifetime 2129 Assembly Instructions And Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual